Linux Ethernet-Howto
by Paul Gortmaker
v2.66, 6 July 1998
This is the Ethernet-Howto, which is a compilation of information
about which ethernet devices can be used for Linux, and how to set
them up. It hopefully answers all the frequently asked questions about
using ethernet cards with Linux. Note that this Howto is focused on
the hardware and low level driver aspect of the ethernet cards, and
does not cover the software end of things like ifconfig and route. See
the Network Howto for that stuff.
______________________________________________________________________
Table of Contents
1. Introduction
1.1 New Versions of this Document
1.2 Using the Ethernet-Howto
1.3 HELP - It doesn't work!
2. What card should I buy for Linux?
2.1 So What Drivers are Stable?
2.2 Eight bit vs 16 bit Cards
2.3 32 Bit (VLB/EISA/PCI) Ethernet Cards
2.4 Available 100Mbs Cards and Drivers
2.5 100VG versus 100BaseT
2.6 Programmed I/O vs. Shared Memory vs. DMA
2.6.1 Programmed I/O (e.g. NE2000, 3c509)
2.6.2 Shared memory (e.g. WD80x3, SMC-Ultra, 3c503)
2.6.3 Slave (normal) Direct Memory Access (e.g. none for Linux!)
2.6.4 Bus Master Direct Memory Access (e.g. LANCE, DEC 21040)
2.7 Type of cable that your card should support
3. Frequently Asked Questions
3.1 Alpha Drivers -- Getting and Using them
3.2 Using More than one Ethernet Card per Machine
3.3 Poor NE2000 Clones
3.4 Problems with NE1000 / NE2000 cards (and clones)
3.5 Problems with SMC Ultra/EtherEZ and WD80*3 cards
3.6 Problems with 3Com cards
3.7 FAQs Not Specific to Any Card.
3.7.1 Ethercard is Not Detected at Boot.
3.7.2 (TT
3.7.3 PCI machine detects card but driver fails probe.
3.7.4 Shared Memory ISA cards in PCI Machine dont work (0xffff)
3.7.5 NexGen machine gets `mismatched read page pointers' errors.
3.7.6 Asynchronous Transfer Mode (ATM) Support
3.7.7 Gigabyte Ethernet Support
3.7.8 FDDI Support
3.7.9 Full Duplex Support
3.7.10 Ethernet Cards for Linux on Alpha/AXP PCI Boards
3.7.11 Ethernet for Linux on SUN/Sparc Hardware.
3.7.12 Linking 10BaseT without a Hub
3.7.13 SIOCSIFxxx: No such device
3.7.14 SIOCSFFLAGS: Try again
3.7.15 Using `ifconfig' and Link UNSPEC with HW-addr of 00:00:00:00:00:00
3.7.16 Huge Number of RX and TX Errors
3.7.17 Entries in
3.7.18 Linux and ``trailers''
3.7.19 Access to the raw Ethernet Device
4. Performance Tips
4.1 General Concepts
4.2 ISA Bus Speed
4.3 Setting the TCP Rx Window
4.4 Increasing NFS performance
5. Vendor/Manufacturer/Model Specific Information
5.1 3Com
5.1.1 3c501
5.1.2 EtherLink II, 3c503, 3c503/16
5.1.3 3c505
5.1.4 3c507
5.1.5 3c509 / 3c509B
5.1.6 3c515
5.1.7 3c523
5.1.8 3c527
5.1.9 3c529
5.1.10 3c562
5.1.11 3c575
5.1.12 3c579
5.1.13 3c589 / 3c589B
5.1.14 3c590 / 3c595
5.1.15 3c592 / 3c597
5.1.16 3c900 / 3c905 / 3c905B
5.2 Accton
5.2.1 Accton MPX
5.2.2 Accton EN1203, EN1207, EtherDuo-PCI
5.2.3 Accton EN2209 Parallel Port Adaptor (EtherPocket)
5.2.4 Accton EN2212 PCMCIA Card
5.3 Allied Telesyn/Telesis
5.3.1 AT1500
5.3.2 AT1700
5.3.3 AT2450
5.3.4 AT2540FX
5.4 AMD / Advanced Micro Devices
5.4.1 AMD LANCE (7990, 79C960/961/961A, PCnet-ISA)
5.4.2 AMD 79C965 (PCnet-32)
5.4.3 AMD 79C970/970A (PCnet-PCI)
5.4.4 AMD 79C971 (PCnet-FAST)
5.4.5 AMD 79C974 (PCnet-SCSI)
5.5 Ansel Communications
5.5.1 AC3200 EISA
5.6 Apricot
5.6.1 Apricot Xen-II On Board Ethernet
5.7 Arcnet
5.8 AT&T
5.8.1 AT&T T7231 (LanPACER+)
5.9 AT-Lan-Tec / RealTek
5.9.1 AT-Lan-Tec / RealTek Pocket adaptor
5.9.2 RealTek 8009
5.9.3 RealTek 8019
5.9.4 RealTek 8029
5.9.5 RealTek 8129/8139
5.10 Boca Research
5.10.1 Boca BEN (ISA, VLB, PCI)
5.11 Cabletron
5.11.1 E10**, E10**-x, E20**, E20**-x
5.11.2 E2100
5.11.3 E22**
5.12 Cogent
5.12.1 EM100-ISA/EISA
5.12.2 Cogent eMASTER+, EM100-PCI, EM400, EM960, EM964
5.13 Compaq
5.13.1 Compaq Deskpro / Compaq XL (Embedded AMD Chip)
5.14 Danpex
5.14.1 Danpex EN9400
5.15 D-Link
5.15.1 DE-100, DE-200, DE-220-T, DE-250
5.15.2 DE-520
5.15.3 DE-530
5.15.4 DE-600
5.15.5 DE-620
5.15.6 DE-650
5.16 DFI
5.16.1 DFINET-300 and DFINET-400
5.17 Digital / DEC
5.17.1 DEPCA, DE100/1, DE200/1/2, DE210, DE422
5.17.2 Digital EtherWorks 3 (DE203, DE204, DE205)
5.17.3 DE425 (EISA), DE434, DE435, DE500
5.17.4 DEC 21040, 21041, 2114x, Tulip
5.18 Farallon
5.18.1 Farallon Etherwave
5.19 Hewlett Packard
5.19.1 27245A
5.19.2 HP EtherTwist, PC Lan+ (27247, 27252A)
5.19.3 HP-J2405A
5.19.4 HP-Vectra On Board Ethernet
5.19.5 HP 10/100 VG Any Lan Cards (27248B, J2573, J2577, J2585)
5.19.6 HP NetServer 10/100TX PCI (D5013A)
5.20 IBM / International Business Machines
5.20.1 IBM Thinkpad 300
5.20.2 IBM Credit Card Adaptor for Ethernet
5.20.3 IBM Token Ring
5.21 ICL Ethernet Cards
5.21.1 ICL EtherTeam 16i/32
5.22 Intel Ethernet Cards
5.22.1 Ether Express
5.22.2 Ether Express PRO/10
5.22.3 Ether Express PRO/10 PCI (EISA)
5.22.4 Ether Express PRO 10/100B
5.23 Kingston
5.24 LinkSys
5.24.1 LinkSys Etherfast 10/100 Cards.
5.24.2 LinkSys Pocket Ethernet Adapter Plus (PEAEPP)
5.24.3 LinkSys PCMCIA Adaptor
5.25 Microdyne
5.25.1 Microdyne Exos 205T
5.26 Mylex
5.26.1 Mylex LNE390A, LNE390B
5.26.2 Mylex LNP101
5.26.3 Mylex LNP104
5.27 Novell Ethernet, NExxxx and associated clones.
5.27.1 NE1000, NE2000
5.27.2 NE2000-PCI (RealTek/Winbond/Compex)
5.27.3 NE-10/100
5.27.4 NE1500, NE2100
5.27.5 NE3200
5.27.6 NE5500
5.28 Proteon
5.28.1 Proteon P1370-EA
5.28.2 Proteon P1670-EA
5.29 Pure Data
5.29.1 PDUC8028, PDI8023
5.30 Racal-Interlan
5.30.1 ES3210
5.30.2 NI5010
5.30.3 NI5210
5.30.4 NI6510 (not EB)
5.30.5 EtherBlaster (aka NI6510EB)
5.31 Sager
5.31.1 Sager NP943
5.32 Schneider & Koch
5.32.1 SK G16
5.33 SEEQ
5.33.1 SEEQ 8005
5.34 SMC (Standard Microsystems Corp.)
5.35 Thomas Conrad
5.35.1 Thomas Conrad TC-5048
5.36 Western Digital / SMC
5.36.1 WD8003, SMC Elite
5.36.2 WD8013, SMC Elite16
5.36.3 SMC Elite Ultra
5.36.4 SMC Elite Ultra32 EISA
5.36.5 SMC EtherEZ (8416)
5.36.6 SMC EtherPower PCI (8432)
5.36.7 SMC EtherPower II PCI (9432)
5.36.8 SMC 3008
5.36.9 SMC 3016
5.36.10 SMC-9000 / SMC 91c92/4
5.36.11 SMC 91c100
5.37 Xircom
5.37.1 PE1, PE2, PE3-10B*
5.38 Zenith
5.38.1 Z-Note
5.39 Znyx
5.39.1 Znyx ZX342 (DEC 21040 based)
5.40 Identifying an Unknown Card
5.40.1 Identifying the Network Interface Controller
5.40.2 Identifying the Ethernet Address
5.40.3 Tips on Trying to Use an Unknown Card
5.41 Drivers for Non-Ethernet Devices
6. Cables, Coax, Twisted Pair
6.1 Thin Ethernet (thinnet)
6.2 Twisted Pair
6.3 Thick Ethernet
7. Software Configuration and Card Diagnostics
7.1 Configuration Programs for Ethernet Cards
7.1.1 WD80x3 Cards
7.1.2 Digital / DEC Cards
7.1.3 NE2000+ or AT/LANTIC Cards
7.1.4 3Com Cards
7.2 Diagnostic Programs for Ethernet Cards
8. Technical Information
8.1 Probed Addresses
8.2 Writing a Driver
8.3 Driver interface to the kernel
8.3.1 Probe
8.3.2 Interrupt handler
8.3.3 Transmit function
8.3.4 Receive function
8.3.5 Open function
8.3.6 Close function (optional)
8.3.7 Miscellaneous functions
8.4 Interrupts and Linux
8.5 Programming the Intel chips (i82586 and i82593)
8.6 Technical information from 3Com
8.7 Notes on AMD PCnet / LANCE Based cards
8.8 Multicast and Promiscuous Mode
8.9 The Berkeley Packet Filter (BPF)
9. Networking with a Laptop/Notebook Computer
9.1 Using SLIP
9.2 Built in NE2000
9.3 PCMCIA Support
9.4 ISA Ethercard in the Docking Station.
9.5 Pocket / parallel port adaptors.
10. Miscellaneous.
10.1 Passing Ethernet Arguments to the Kernel
10.1.1 The
10.1.2 The
10.2 Using the Ethernet Drivers as Modules
10.3 Mailing Lists and the Linux Newsgroups
10.4 Related Documentation
10.5 Contributors
10.6 Disclaimer and Copyright
10.7 Closing
______________________________________________________________________
1. Introduction
The Ethernet-Howto covers what cards you should and shouldn't buy; how
to set them up, how to run more than one, and other common problems
and questions. It contains detailed information on the current level
of support for all of the most common ethernet cards available.
It does not cover the software end of things, as that is covered in
the NET-3 Howto. Also note that general non-Linux specific questions
about Ethernet are not (or at least they should not be) answered here.
For those types of questions, see the excellent amount of information
in the comp.dcom.lans.ethernet FAQ. You can FTP it from rtfm.mit.edu
just like all the other newsgroup FAQs.
This present revision covers distribution kernels up to and including
2.0.34. Some information pertaining to development kernels up to
version 2.1.108 is also included.
The Ethernet-Howto is by:
Paul Gortmaker, gpg109@rsphy1.anu.edu.au
The primary source of information for the initial ASCII-only version
of the Ethernet-Howto was:
Donald J. Becker, becker@cesdis.gsfc.nasa.gov
who we should thank for writing the vast majority of ethernet card
drivers that are presently available for Linux. He also is the
original author of the NFS server too. Thanks Donald!
Please see the Disclaimer and Copying information at the end of this
document for information about redistribution of this document and the
usual `we are not responsible for what you do...' legal stuff.
1.1. New Versions of this Document
New versions of this document can be retrieved via anonymous FTP from:
Sunsite HOWTO Archive
and various Linux ftp mirror sites. Updates will be made as new
information and/or drivers becomes available. If this copy that you
are reading is more than 6 months old, it is either out of date, or it
means that I have been lazy and haven't updated it.
If you have sent me an update and it is not included in the next
release, it probably means I've lost it amongst the ton of junk e-mail
I get. Please re-send it (along with an abusive message) and I will
try and make sure it gets included in the next release.
This document was produced by using the SGML system that was
specifically set up for the Linux Howto project, and there are various
output formats available, including, postscript, dvi, ascii, html, and
soon TeXinfo.
I would recommend viewing it in the html (via a WWW browser) or the
Postscript/dvi format. Both of these contain cross-references that are
lost in the ascii format.
If you want to get the latest copy off sunsite, here is URL.
Ethernet-HOWTO
1.2. Using the Ethernet-Howto
As this guide is getting bigger and bigger, you probably don't want to
spend the rest of your afternoon reading the whole thing. And the good
news is that you don't have to read it all.
Chances are you are reading this document beacuse you can't get things
to work and you don't know what to do or check. The next section
(``HELP - It doesn't work!'') is aimed at newcomers to linux and will
point you in the right direction.
Typically the same problems and questions are asked over and over
again by different people. Chances are your specific problem or
question is one of these frequently asked questions, and is answered
in the FAQ portion of this document . (``The FAQ section'').
Everybody should have a look through this section before posting for
help.
If you haven't got an ethernet card, then you will want to start with
deciding on a card. (``What card should I buy...'')
If you have already got an ethernet card, but are not sure if you can
use it with Linux, then you will want to read the section which
contains specific information on each manufacturer, and their cards.
(``Vendor Specific...'')
If you are interested in some of the technical aspects of the Linux
device drivers, then you can have a browse of the section with this
type of information. (``Technical Information'')
1.3. HELP - It doesn't work!
Okay, don't panic. This will lead you through the process of getting
things working, even if you have no prior background in linux or
ethernet hardware.
First thing you need to do is figure out what model your card is so
you can determine if Linux has a driver for that particular card.
Different cards typically have different ways of being controlled by
the host computer, and the linux driver (if there is one) contains
this control information in a format that allows linux to use the
card. If you don't have any manuals or anything of the sort that tell
you anything about the card model, then you can try the section on
helping with mystery cards (reference section: ``Identifying an
Unknown Card'').
Now that you know what type of card you have, read through the details
of your particular card in the card specific section (reference
section: ``Vendor Specific...'') which lists in alphabetical order,
card manufacturers, individual model numbers and whether it has a
linux driver or not. If it lists it as `Not Supported' you can pretty
much give up here. If you can't find your card in that list, then
check to see if your card manual lists it as being `compatible' with
another known card type. For example there are hundreds, if not
thousands of different cards made to be compatible with the original
Novell NE2000 design.
Assuming you have found out that a linux driver exists for your card,
you now have to find it and make use of it. Just because linux has a
driver for your card does not mean that it is built into every kernel.
(The kernel is the core operating system that is first loaded at boot,
and contains drivers for various pieces of hardware, among other
things.) Depending on who made the particular linux distribution you
are using, there may be only a few pre-built kernels, and a whole
bunch of drivers as smaller separate modules, or there may be a whole
lot of kernels, covering a vast combination of built-in driver
combinations.
Most linux distributions now ship with a bunch of small modules that
are the various drivers. The required modules are typically loaded
late in the boot process, or on-demand as a driver is needed to access
a particualr device. You will need to attach this module to the
kernel after it has booted up. See the information that came with your
distribution on installing and using modules, along with the module
section in this document. (``Using the Ethernet Drivers as Modules'')
If you didn't find either a pre-built kernel with your driver, or a
module form of the driver, chances are you have a typically uncommon
card, and you will have to build your own kernel with that driver
included. Once you have linux installed, building a custom kernel is
not difficult at all. You essentially answer yes or no to what you
want the kernel to contain, and then tell it to build it. There is a
Kernel-HowTo that will help you along.
At this point you should have somehow managed to be booting a kernel
with your driver built in, or be loading it as a module. About half
of the problems people have are related to not having driver loaded
one way or another, so you may find things work now.
If it still doesn't work, then you need to verify that the kernel is
indeed detecting the card. To do this, you need to type dmesg | more
when logged in after the system has booted and all modules have been
loaded. This will allow you to review the boot messages that the
kernel scrolled up the screen during the boot process. If the card
has been detected, you should see somewhere in that list a message
from your card's driver that starts with eth0, mentions the driver
name and the hardware parameters (interrupt setting, input/output port
address, etc) that the card is set for. If you don't see a message
like this, then the driver didn't detect your card, and that is why
things aren't working. See the FAQ (``The FAQ Section'') for what to
do if your card is not detected. If you have a NE2000 compatible,
there is also some NE2000 specific tips on getting a card detected in
the FAQ section as well.
If the card is detected, but the detection message reports some sort
of error, like a resource conflict, then the driver probably won't
have initialized properly and the card still wont be useable. Most
common error messages of this sort are also listed in the FAQ section,
along with a solution.
If the detection message seems okay, then double check the card
resources reported by the driver against those that the card is
physically set for (either by little black jumpers on the card, or by
a software utility supplied by the card manufacturer.) These must
match exactly. For example, if you have the card jumpered or
configured to IRQ 15 and the driver reports IRQ 10 in the boot
messages, things will not work. The FAQ section discusses the most
common cases of drivers incorrectly detecting the configuration
information of various cards.
At this point, you have managed to get you card detected with all the
correct parameters, and hopefully everything is working. If not, then
you either have a software configuration error, or a hardware
configuration error. A software configuration error is not setting up
the right network addresses for the ifconfig and route commands, and
details of how to do that are fully described in the Network HowTo and
the `Network Administrator's Guide' which both probably came on the
CD-ROM you installed from.
A hardware configuration error is when some sort of resource conflict
or mis-configuration (that the driver didn't detect at boot) that
stops the card from working properly. This typically can be observed
in one of three different ways. (1) You get an error message when
ifconfig tries to open the device for use, such as ``SIOCSFFLAGS: Try
again''. (2) The driver reports eth0 error messages (viewed by dmesg |
more) or strange inconsistencies for each time it tries to send or
receive data. (3) Typing cat /proc/net/dev shows non-zero numbers in
one of the errs, drop, fifo, frame or carrier columns for eth0. Most
of the typical hardware configuration errors are also discussed in the
FAQ section.
Well, if you have got to this point and things still aren't working,
read the FAQ section of this document, read the vendor specific
section detailing your particular card, and if it still doesn't work
then you may have to resort to posting to an appropriate newsgroup for
help. If you do post, please detail all relevant information in that
post, such as the card brand, the kernel version, the driver boot
messages, the output from cat /proc/net/dev, a clear description of
the problem, and of course what you have already tried to do in an
effort to get things to work.
You would be surprised at how many people post useless things like
``Can someone help me? My ethernet doesn't work.'' and nothing else.
Readers of the newsgroups tend to ignore such silly posts, whereas a
detailed and informational problem description may allow a `linux-
guru' to spot your problem right away.
2. What card should I buy for Linux?
The answer to this question depends heavily on exactly what you intend
on doing with your net connection, and how much traffic it will see.
If you only expect a single user to be doing the occasional ftp
session or WWW connection, then even an old 8 bit ISA card will
probably keep you happy.
If you intend to set up a server, and you require the CPU overhead of
Rx'ing and Tx'ing network data to be kept to a minimum, you probably
want to look at one of the newer PCI cards that has bus-mastering
capapbility, such as with the DEC tulip (21xxx) chip, or the AMD
PCnet-PCI chip.
If you fall somewhere in the middle of the above, then any one of the
16 bit ISA cards with stable drivers will do the job for you.
2.1. So What Drivers are Stable?
Of the 16 bit ISA cards, the following drivers are very mature, and
you shouldn't have any problems if you buy a card that uses these
drivers.
SMC-Ultra/EtherEZ, SMC-Elite (WD80x3), 3c509, Lance, NE2000.
This is not to say that all the other drivers are unstable. It just
happens that the above are the oldest and most used of all the linux
drivers, making them the safest choice.
Note that some el-cheapo motherboards can have trouble with the bus-
mastering that the ISA Lance cards do, and some el-cheapo NE2000
clones can have trouble getting detected at boot.
The most commonly used linux PCI drivers are probably the 3Com
Vortex/Boomerang (3c59x/3c9xx), the DEC tulip (21xxx), and the Intel
EtherExpressPro 100. The various PCI-NE2000 clone cards are also
extremely common, but purchasing a PCI-NE2000 clone card is not
recommended unless the lowest possible price is more important than
having a modern high-performace design card.
2.2. Eight bit vs 16 bit Cards
You probably can't buy a new 8 bit ISA ethercard anymore, but you will
find lots of them turning up at computer swap meets and the like for
the next few years, at very low prices. This will make them popular
for ``home-ethernet'' systems. The above holds true for 16 bit ISA
cards now as well, since PCI cards are now very common.
Some 8 bit cards that will provide adequate performance for light to
average use are the wd8003, the 3c503 and the ne1000. The 3c501
provides poor performance, and these poor 12 year old relics of the XT
days should be avoided.
The 8 bit data path doesn't hurt performance that much, as you can
still expect to get about 500 to 800kB/s ftp download speed to an 8
bit wd8003 card (on a fast ISA bus) from a fast host. And if most of
your net-traffic is going to remote sites, then the bottleneck in the
path will be elsewhere, and the only speed difference you will notice
is during net activity on your local subnet.
2.3. 32 Bit (VLB/EISA/PCI) Ethernet Cards
Note that a 10Mbs network typically doesn't justify requiring a 32
bit interface. See ``Programmed I/O vs. ...'' as to why having a
10Mbps ethercard on an 8MHz ISA bus is really not a bottleneck. Even
though having the ethercard on a fast bus won't necessarily mean
faster transfers, it will usually mean reduced CPU overhead, which is
good for multi-user systems.
Of course for 100Mbps networks, which are now commonplace, the 32 bit
interface is a must to make use of the full bandwidth. AMD has the 32
bit PCnet-VLB and PCnet-PCI chips. See ``AMD PCnet-32'' for info on
the 32 bit versions of the LANCE / PCnet-ISA chip.
The DEC 21xxx PCI `tulip' chip is another option (see ``DEC 21040'')
for power-users. Many manufacturers produce cards that use this chip,
and the prices of such no-name cards is usually quite cheap.
3Com's `Vortex' and `Boomerang' PCI cards are also another option, and
the price is quite cheap if you can get one under their evaluation
deal while it lasts. (see ``3c590/3c595'')
Intel's EtherExpress Pro 10/100 PCI cards have also been reported to
work well with linux. (see ``EtherExpress'')
Various clone manufacturers have started making PCI NE2000 clones
based on a RealTek or Winbond chip. These cards are also supported by
the linux ne2000 driver for v2.0.31 and newer kernels. However you
only benefit from the faster bus interface, as the card is still using
the age-old ne2000 driver interface. As of v2.0.34 (and above) a
separate PCI-specific driver for these cards ne2k-pci.c is also
available, which will be sightly more efficient than the ISA ne.c
driver.
2.4. Available 100Mbs Cards and Drivers
The present list of supported 100Mbs hardware is as follows: cards
with the DEC 21140 chip; the 3c595/3c90x Vortex cards; and the HP
100VG ANY-LAN. The drivers for the first two are quite stable, but
feedback on the HP driver has been low so far.
The EtherExpressPro10/100B now also has a driver in the current v2.0
kenrel. For updates and/or support, see the relevant section in this
document.
The 21140 100Base-? chip is supported with the same driver as its
10Mbs counterpart, the 21040. SMC's 100Mbs EtherPower PCI card uses
this chip. As with the 21040, you have a choice of two drivers to pick
from.
Also have a look at the information on Donald's WWW site, at the
following URL:
100Mbs Ethernet
Donald had done a fair bit of work with the SMC EtherPower-10/100
cards, and reported getting about 4.6MB/s application to application
with TCP on P5-100 Triton machines.
(See ``3c595'' and ``DEC 21140'' for more details.)
For 100VG information, see the following section, and this URL on
Donald's Site:
Donald's 100VG Page
You may also be interested in looking at:
Dan Kegel's Fast Ethernet Page
2.5. 100VG versus 100BaseT
100BaseT is much more prominent than 100VG, and the following blurb
from an older one of Donald's informative comp.os.linux postings
summarizes the situation quite well:
``For those not in the know, there are two competing 100Mbs ethernet
standards, 100VG (aka 100baseVG and 100VG-AnyLAN) and 100baseT (with
100baseTx, 100baseT4 and 100baseFx cable types).
100VG was on the market first, and I feel that it is better engineered
than 100baseTx. I was rooting for it to win, but it clearly isn't
going to. HP et al. made several bad choices:
1) Delaying the standard so that they could accommodate IBM and
support token ring frames. It `seemed like a good idea at the time',
since it would enable token ring shops to upgrade without the managers
having to admit they made a very expensive mistake committing to the
wrong technology. But there was nothing to be gained, as the two
frame types couldn't coexist on a network, token ring is a morass of
complexity, and IBM went with 100baseT anyway.
2) Producing only ISA and EISA cards. (A PCI model was only recently
announced.) The ISA bus is too slow for 100mbs, and relatively few
EISA machines exist. At the time VLB was common, fast, and cheap with
PCI a viable choice. But "old-timer" wisdom held that servers would
stay with the more expensive EISA bus.
3) Not sending me a databook. Yes, this action was the real reason
for the 100VGs downfall :-). I called all over for programming info,
and all I could get was a few page color glossy brochure from AT&T
describing how wonderful the Regatta chipset was.''
2.6. Programmed I/O vs. Shared Memory vs. DMA
If you can already send and receive back-to-back packets, you just
can't put more bits over the wire. Every modern ethercard can receive
back-to-back packets. The Linux DP8390 drivers (wd80x3, SMC-Ultra,
3c503, ne2000, etc) come pretty close to sending back-to-back packets
(depending on the current interrupt latency) and the 3c509 and AT1500
hardware have no problem at all automatically sending back-to-back
packets.
The ISA bus can do 5.3MB/sec (42Mb/sec), which sounds like more than
enough for 10Mbps ethernet. In the case of the 100Mbps cards, you
clearly need a faster bus to take advantage of the network bandwidth.
2.6.1. Programmed I/O (e.g. NE2000, 3c509)
Pro: Doesn't use any constrained system resources, just a few I/O
registers, and has no 16M limit.
Con: Usually the slowest transfer rate, the CPU is waiting the whole
time, and interleaved packet access is usually difficult to
impossible.
2.6.2. Shared memory (e.g. WD80x3, SMC-Ultra, 3c503)
Pro: Simple, faster than programmed I/O, and allows random access to
packets. The linux drivers compute the checksum of incoming IP packets
as they are copied off the card, resulting in a further reduction of
CPU usage vs. an equivalent PIO card.
Con: Uses up memory space (a big one for DOS users, essentially a non-
issue under Linux), and it still ties up the CPU.
2.6.3. Slave (normal) Direct Memory Access (e.g. none for Linux!)
Pro: Frees up the CPU during the actual data transfer.
Con: Checking boundary conditions, allocating contiguous buffers, and
programming the DMA registers makes it the slowest of all techniques.
It also uses up a scarce DMA channel, and requires aligned low memory
buffers.
2.6.4. Bus Master Direct Memory Access (e.g. LANCE, DEC 21040)
Pro: Frees up the CPU during the data transfer, can string together
buffers, can require little or no CPU time lost on the ISA bus. Most
of the bus-mastering linux drivers now use a `copybreak' scheme where
large packets are put directly into a kernel networking buffer by the
card, and small packets are copied by the CPU which primes the cache
for subsequent processing.
Con: (Only applicable to ISA bus cards) Requires low-memory buffers
and a DMA channel for cards. Any bus-master will have problems with
other bus-masters that are bus-hogs, such as some primitive SCSI
adaptors. A few badly-designed motherboard chipsets have problems with
bus-masters. And a reason for not using any type of DMA device is
using a 486 processor designed for plug-in replacement of a 386: these
processors must flush their cache with each DMA cycle. (This includes
the Cx486DLC, Ti486DLC, Cx486SLC, Ti486SLC, etc.)
2.7. Type of cable that your card should support
If you are setting up a small ``personal'' network, you will probably
want to use thinnet or thin ethernet cable. This is the style with the
standard BNC connectors. See ``Cables, Coax...'' for other concerns
with different types of ethernet cable.
Most ethercards also come in a `Combo' version for only $10-$20 more.
These have both twisted pair and thinnet transceiver built-in,
allowing you to change your mind later.
The twisted pair cables, with the RJ-45 (giant phone jack) connectors
is technically called 10BaseT. You may also hear it called UTP
(Unsheilded Twisted Pair).
The thinnet, or thin ethernet cabling, (RG-58 coaxial cable) with the
BNC (metal push and turn-to-lock) connectors is technically called
10Base2.
The older thick ethernet (10mm coaxial cable) which is only found in
older installations is called 10Base5.
Large corporate installations will most likely use 10BaseT instead of
10Base2. 10Base2 does not offer an easy upgrade path to the new
upcoming 100Base-whatever.
3. Frequently Asked Questions
Here are some of the more frequently asked questions about using Linux
with an Ethernet connection. Some of the more specific questions are
sorted on a `per manufacturer basis'. However, since this document is
basically `old' by the time you get it, any `new' problems will not
appear here instantly. For these, I suggest that you make efficient
use of your newsreader. For example, nn users would type
nn -xX -s'3c'
to get all the news articles in your subscribed list that have `3c' in
the subject. (ie. 3com, 3c509, 3c503, etc.) The moral: Read the man
page for your newsreader.
3.1. Alpha Drivers -- Getting and Using them
I heard that there is an updated or alpha driver available for my
card. Where can I get it?
The newest of the `new' drivers can be found on Donald's ftp site:
cesdis.gsfc.nasa.gov in the /pub/linux/ area. Things change here quite
frequently, so just look around for it. Alternatively, it may be
easier to use a WWW browser on:
Don's Linux Home Page
to locate the driver that you are looking for. (Watch out for WWW
browsers that silently munge the source by replacing TABs with spaces
and so on - use ftp, or at least an FTP URL for downloading if
unsure.)
Now, if it really is an alpha, or pre-alpha driver, then please treat
it as such. In other words, don't complain because you can't figure
out what to do with it. If you can't figure out how to install it,
then you probably shouldn't be testing it. Also, if it brings your
machine down, don't complain. Instead, send us a well documented bug
report, or even better, a patch!
Note that some of the `useable' experimental/alpha drivers have been
included in the standard kernel source tree. When running make config
one of the first things you will be asked is whether to ``Prompt for
development and/or incomplete code/drivers''. You will have to answer
`Y' here to get asked about including any alpha/experiemntal drivers.
3.2. Using More than one Ethernet Card per Machine
What needs to be done so that Linux can run two ethernet cards?
With the Driver as a Module: Most linux distributions use modular
drivers now (as opposed to having the driver built into the kernel).
In the case of PCI drivers, the module will typically detect all of
the installed cards of that brand model automatically. However, for
ISA cards, probing for a card is not a safe operation, and hence you
typically need to supply the I/O base address of the card so the
module knows where to look. This information is typically stored in
the file /etc/conf.modules.
As an example, consider a user that has two ISA NE2000 cards, one at
0x300 and one at 0x240 and what lines they would have in their
/etc/conf.modules file:
alias eth0 ne
alias eth1 ne
options ne io=0x240,0x300
What this does: This says that if the administrator (or the kernel)
does a modprobe eth0 or a modprobe eth1 then the ne.o driver should be
loaded for either eth0 or eth1. Furthermore, when the ne.o module is
loaded, it should be loaded with the options io=0x240,0x300 so that
the driver knows where to look for the cards. Note that the 0x is
important - things like 300h as commonly used in the DOS world won't
work. Switching the order of the 0x240 and the 0x300 will switch
which physical card ends up as eth0 and eth1.
Most of the ISA module drivers can take multiple comma separated i/o
values like this example to handle multiple cards. However, some
(older?) drivers, such as the 3c501.o module are currently only able
to handle one card per module load. In this case you can load the
module twice to get both cards detected. The /etc/conf.modules file in
this case would look like:
alias eth0 3c501
alias eth1 3c501
options eth0 -o 3c501-0 io=0x280 irq=5
options eth1 -o 3c501-1 io=0x300 irq=7
In this example the -o option has been used to give each instance of
the module a unique name, since you can't have two modules loaded with
the same name. The irq= option has also been used to to specify the
hardware IRQ setting of the card. (This method can also be used with
modules that accept comma separated i/o values, but it is less
efficient since the module ends up being loaded twice when it doesn't
really need to be.)
As a final example, consider a user with one 3c503 card at 0x350and
one SMC Elite16 (wd8013) card at 0x280. They would have:
alias eth0 wd
alias eth1 3c503
options wd io=0x280
options 3c503 io=0x350
For PCI cards, you typically only need the alias lines to correlate
the ethN interfaces with the appropriate driver name, since the I/O
base of a PCI card can be safely detected.
The available modules are typically stored in /lib/modules/`uname
-r`/net where the uname -r command gives the kernel version (e.g.
2.0.34). You can look in there to see which one matches your card.
Once you have the correct settings in your conf.modules file, you can
test things out with:
modprobe ethN
dmesg | tail
where `N' is the number of the ethernet interface you are testing.
With the Driver Compiled into the Kernel: If you have the driver
compiled into the kernel, then the hooks for multiple ethercards are
all there. However, note that at the moment only one ethercard is
auto-probed for by default. This helps to avoid possible boot time
hangs caused by probing sensitive cards.
There are two ways that you can enable auto-probing for the second
(and third, and...) card. The easiest method is to pass boot-time
arguments to the kernel, which is usually done by LILO. Probing for
the second card can be achieved by using a boot-time argument as
simple as ether=0,0,eth1. In this case eth0 and eth1 will be assigned
in the order that the cards are found at boot. Say if you want the
card at 0x300 to be eth0 and the card at 0x280 to be eth1 then you
could use
LILO: linux ether=5,0x300,eth0 ether=15,0x280,eth1
The ether= command accepts more than the IRQ + i/o + name shown above.
Please have a look at ``Passing Ethernet Arguments...'' for the full
syntax, card specific parameters, and LILO tips.
These boot time arguments can be made permanent so that you don't have
to re-enter them every time. See the LILO configuration option
`append' in the LILO manual.
The second way (not recommended) is to edit the file Space.c and
replace the 0xffe0 entry for the i/o address with a zero. The 0xffe0
entry tells it not to probe for that device -- replacing it with a
zero will enable autoprobing for that device.
Note that if you are intending to use Linux as a gateway between two
networks, you will have to re-compile a kernel with IP forwarding
enabled. Usually using an old AT/286 with something like the `kbridge'
software is a better solution.
If you are viewing this while net-surfing, you may wish to look at a
mini-howto Donald has on his WWW site. Check out Multiple Ethercards
.
3.3. Poor NE2000 Clones
Here is a list of some of the NE-2000 clones that are known to have
various problems. Most of them aren't fatal. In the case of the ones
listed as `bad clones' -- this usually indicates that the cards don't
have the two NE2000 identifier bytes. NEx000-clones have a Station
Address PROM (SAPROM) in the packet buffer memory space. NE2000
clones have 0x57,0x57 in bytes 0x0e,0x0f of the SAPROM, while other
supposed NE2000 clones must be detected by their SA prefix.
This is not a comprehensive list of all the NE2000 clones that don't
have the 0x57,0x57 in bytes 0x0e,0x0f of the SAPROM. There are
probably hundreds of them. If you get a card that causes the driver to
report an `invalid signature' then you will have to add your cards
signature to the driver. The process for doing this is described
below.
Accton NE2000 -- might not get detected at boot, see below.
Artisoft LANtastic AE-2 -- OK, but has flawed error-reporting
registers.
AT-LAN-TEC NE2000 -- clone uses Winbond chip that traps SCSI drivers
ShineNet LCS-8634 -- clone uses Winbond chip that traps SCSI drivers
Cabletron E10**, E20**, E10**-x, E20**-x -- bad clones, but the driver
checks for them. See ``E10**''.
D-Link Ethernet II -- bad clones, but the driver checks for them. See
``DE-100 / DE-200''.
DFI DFINET-300, DFINET-400 -- bad clones, but the driver checks for
them. See ``DFI-300 / DFI-400''
EtherNext UTP8, EtherNext UTP16 -- bad clones, but the driver checks
for them.
3.4. Problems with NE1000 / NE2000 cards (and clones)
Problem: PCI NE2000 clone card is not detected at boot with v2.0.x.
Reason: The ne.c driver up to v2.0.30 only knows about the PCI ID
number of RealTek 8029 based clone cards. Since then, several others
have also released PCI NE2000 clone cards, with different PCI ID
numbers, and hence the driver doesn't detect them.
Solution: The easiest solution is to upgrade to a v2.0.31 (or newer)
version of the linux kernel. It knows the ID numbers of about five
different NE2000-PCI chips, and will detect them automatically at boot
or at module loading time. If you upgrade to 2.0.34 (or newer) there
is a PCI-only specific NE2000 driver that is slightly smaller and more
efficient than the original ISA/PCI driver.
Problem: PCI NE2000 clone card is reported as an ne1000 (8 bit card!)
at boot or when I load the ne.o module for v2.0.x, and hence doesn't
work.
Reason: Some PCI clones don't implement byte wide access (and hence
are not truly 100% NE2000 compatible). This causes the probe to think
they are NE1000 cards.
Solution: You need to upgrade to v2.0.31 (or newer) as described
above. The driver(s) now check for this hardware bug.
Problem: PCI NE2000 card gets terrible performance, even when reducing
the window size as described in the Performance Tips section.
Reason: The spec sheets for the original 8390 chip, desgined and sold
over ten years ago, noted that a dummy read from the chip was required
before each write operation for maximum reliablity. The driver has
the facility to do this but it has been disabled by default since the
v1.2 kernel days. One user has reported that re-enabling this `mis-
feature' helped their performance with a cheap PCI NE2000 clone card.
Solution: Since it has only been reported as a solution by one person,
don't get your hopes up. Re-enabling the read before write fix is done
by simply editing the file linux/drivers/net/ne.c, uncommenting the
line containing NE_RW_BUGFIX and then rebuilding the kernel or module
as appropriate. Please send an e-mail describing the performance
difference and type of card/chip you have if this helps you. (The same
can be done for the ne2k-pci.c driver as well).
Probem: ISA Plug and Play NE2000 (such as RealTek 8019) is not
detected.
Reason: The original NE2000 specification (and hence the linux NE2000
driver) does not have support for Plug and Play.
Solution: Use the DOS configuration disk that came with the card to
disable PnP, and to set the card to a specified I/O address and IRQ.
Add a line to /etc/conf.modules like options ne io=0xNNN where 0xNNN
is the hex I/O address you set the card to. (This assumes you are
using a modular driver; if not then use an ether=0,0xNNN,eth0 argument
at boot). Alternatively, if you need to leave PnP enabled for
compatibility with some other operating system, then look into the
isapnptools package. Try man isapnp to see if it is already installed
on your system. If not, then have a look at the following URL:
ISA PNP Tools
Problem: NE*000 card hangs machine, sometimes with a `DMA conflict'
message, sometimes completely silently.
Reason: There were some bugs in the driver and the upper networking
layers that caused this. They have been fixed long ago, in kernels
v1.2.9 and above. Upgrade your kernel.
Problem: NE*000 card hangs machine during NE probe, or can not read
station address properly.
Reason: Kernels previous to v1.3.7 did not fully reset the card after
finding it at boot. Some cheap cards are not left in a reasonable
state after power-up and need to be fully reset before any attempt is
made to use them. Also, a previous probe may have upset the NE card
prior to the NE probe taking place. In that case, look in to using the
``reserve='' boot keyword to protect the card from other probes.
Problem: NE*000 driver reports `not found (no reset ack)' during boot
probe.
Reason: This is related to the above change. After the initial
verification that an 8390 is at the probed i/o address, the reset is
performed. When the card has completed the reset, it is supposed to
acknowedge that the reset has completed. Your card doesn't, and so
the driver assumes that no NE card is present.
Solution: You can tell the driver that you have a bad card by using an
otherwise unused mem_end hexidecimal value of 0xbad at boot time. You
have to also supply a non-zero i/o base for the card when using the
0xbad override. For example, a card that is at 0x340 that doesn't ack
the reset would use something like:
LILO: linux ether=0,0x340,0,0xbad,eth0
This will allow the card detection to continue, even if your card
doesn't ACK the reset. If you are using the driver as a module, then
you can supply the option bad=0xbad just like you supply the I/O
address. Note that v2.0.x modules won't understand the bad= option, as
it was added during the v2.1 development.
Problem: NE*000 card hangs machine at first network access.
Reason: This problem has been reported for kernels as old as 1.1.57 to
the present. It appears confined to a few software configurable clone
cards. It appears that they expect to be initialized in some special
way.
Solution: Several people have reported that running the supplied DOS
software config program and/or the supplied DOS driver prior to warm
booting (i.e. loadlin or the `three-finger-salute') into linux allowed
the card to work. This would indicate that these cards need to be
initialized in a particular fashion, slightly different than what the
present Linux driver does.
Problem: NE*000 ethercard at 0x360 doesn't get detected anymore.
Reason: Kernels ( > 1.1.7X) have more sanity checks with respect to
overlapping i/o regions. Your NE2000 card is 0x20 wide in i/o space,
which makes it hit the parallel port at 0x378. Other devices that
could be there are the second floppy controller (if equipped) at 0x370
and the secondary IDE controller at 0x376--0x377. If the port(s) are
already registered by another driver, the kernel will not let the
probe happen.
Solution: Either move your card to an address like 0x280, 0x340, 0x320
or compile without parallel printer support.
Problem: Network `goes away' every time I print something (NE2000)
Reason: Same problem as above, but you have an older kernel that
doesn't check for overlapping i/o regions. Use the same fix as above,
and get a new kernel while you are at it.
Problem: NE*000 ethercard probe at 0xNNN: 00 00 C5 ... not found.
(invalid signature yy zz)
Reason: First off, do you have a NE1000 or NE2000 card at the addr.
0xNNN? And if so, does the hardware address reported look like a
valid one? If so, then you have a poor NE*000 clone. All NE*000 clones
are supposed to have the value 0x57 in bytes 14 and 15 of the SA PROM
on the card. Yours doesn't -- it has `yy zz' instead.
Solution: There are two ways to get around this. The easiest is to use
an 0xbad mem_end value as described above for the `no reset ack'
problem. This will bypass the signature check, as long as a non-zero
i/o base is also given. This way no recompilation of the kernel is
required.
The second method involves changing the driver itself, and then
recompiling your kernel. The driver (/usr/src/linux/drivers/net/ne.c)
has a "Hall of Shame" list at about line 42. This list is used to
detect poor clones. For example, the DFI cards use `DFI' in the first
3 bytes of the PROM, instead of using 0x57 in bytes 14 and 15, like
they are supposed to.
You can determine what the first 3 bytes of your card PROM are by
adding a line like:
printk("PROM prefix: %2.2x %2.2x %2.2x\n",SA_prom[0],SA_prom[1],SA_prom[2]);
into the driver, right after the error message you got above, and just
before the "return ENXIO" at line 227.
Reboot with this change in place, and after the detection fails, you
will get the three bytes from the PROM like the DFI example above.
Then you can add your card to the bad_clone_list[] at about line 43.
Say the above line printed out:
PROM prefix: 0x3F 0x2D 0x1C
after you rebooted. And say that the 8 bit version of your card was
called the "FOO-1k" and the 16 bit version the "FOO-2k". Then you
would add the following line to the bad_clone_list[]:
{"FOO-1k", "FOO-2k", {0x3F, 0x2D, 0x1C,}},
Note that the 2 name strings you add can be anything -- they are just
printed at boot, and not matched against anything on the card. You
can also take out the "printk()" that you added above, if you want.
It shouldn't hit that line anymore anyway. Then recompile once more,
and your card should be detected.
Problem: Errors like DMA address mismatch
Is the chip a real NatSemi 8390? (DP8390, DP83901, DP83902 or
DP83905)? If not, some clone chips don't correctly implement the
transfer verification register. MS-DOS drivers never do error
checking, so it doesn't matter to them. (Note: The DMA address check
is not done by default as of v1.2.4 for performance reasons. Enable it
with the `NE_SANITY' define in ne.c if you want the check done.)
Are most of the messages off by a factor of 2? If so: Are you using
the NE2000 in a 16 bit slot? Is it jumpered to use only 8 bit
transfers?
The Linux driver expects a NE2000 to be in a 16 bit slot. A NE1000 can
be in either size slot. This problem can also occur with some clones,
notably older D-Link 16 bit cards, that don't have the correct ID
bytes in the station address PROM.
Are you running the bus faster than 8Mhz? If you can change the speed
(faster or slower), see if that makes a difference. Most NE2000 clones
will run at 16MHz, but some may not. Changing speed can also mask a
noisy bus.
What other devices are on the bus? If moving the devices around
changes the reliability, then you have a bus noise problem -- just
what that error message was designed to detect. Congratulations,
you've probably found the source of other problems as well.
Problem: The machine hangs during boot right after the `8390...' or
`WD....' message. Removing the NE2000 fixes the problem.
Solution: Change your NE2000 base address to something like 0x340.
Alternatively, you can use the ``reserve='' boot argument in
conjunction with the ``ether='' argument to protect the card from
other device driver probes.
Reason: Your NE2000 clone isn't a good enough clone. An active NE2000
is a bottomless pit that will trap any driver autoprobing in its
space. Changing the NE2000 to a less-popular address will move it out
of the way of other autoprobes, allowing your machine to boot.
Problem: The machine hangs during the SCSI probe at boot.
Reason: It's the same problem as above, change the ethercard's
address, or use the reserve/ether boot arguments.
Problem: The machine hangs during the soundcard probe at boot.
Reason: No, that's really during the silent SCSI probe, and it's the
same problem as above.
Problem: NE2000 not detected at boot - no boot messages at all
Solution: There is no `magic solution' as there can be a number of
reasons why it wasn't detected. The following list should help you
walk through the possible problems.
1) Build a new kernel with only the device drivers that you need.
Verify that you are indeed booting the fresh kernel. Forgetting to run
lilo, etc. can result in booting the old one. (Look closely at the
build time/date reported at boot.) Sounds obvious, but we have all
done it before. Make sure the driver is in fact included in the new
kernel, by checking the System.map file for names like ne_probe.
2) Look at the boot messages carefully. Does it ever even mention
doing a ne2k probe such as `NE*000 probe at 0xNNN: not found (blah
blah)' or does it just fail silently. There is a big difference. Use
dmesg|more to review the boot messages after logging in, or hit Shift-
PgUp to scroll the screen up after the boot has completed and the
login prompt appears.
3) After booting, do a cat /proc/ioports and verify that the full
iospace that the card will require is vacant. If you are at 0x300 then
the ne2k driver will ask for 0x300-0x31f. If any other device driver
has registered even one port anywhere in that range, the probe will
not take place at that address and will silently continue to the next
of the probed addresses. A common case is having the lp driver reserve
0x378 or the second IDE channel reserve 0x376 which stops the ne
driver from probing 0x360-0x380.
4) Same as above for cat /proc/interrupts. Make sure no other device
has registered the interrupt that you set the ethercard for. In this
case, the probe will happen, and the ether driver will complain loudly
at boot about not being able to get the desired IRQ line.
5) If you are still stumped by the silent failure of the driver, then
edit it and add some printk() to the probe. For example, with the ne2k
you could add/remove lines (marked with a `+' or `-') in net/ne.c
like:
______________________________________________________________________
int reg0 = inb_p(ioaddr);
+ printk("NE2k probe - now checking %x\n",ioaddr);
- if (reg0 == 0xFF)
+ if (reg0 == 0xFF) {
+ printk("NE2k probe - got 0xFF (vacant i/o port)\n");
return ENODEV;
+ }
______________________________________________________________________
Then it will output messages for each port address that it checks, and
you will see if your card's address is being probed or not.
6) You can also get the ne2k diagnostic from Don's ftp site (mentioned
in the howto as well) and see if it is able to detect your card after
you have booted into linux. Use the `-p 0xNNN' option to tell it where
to look for the card. (The default is 0x300 and it doesn't go looking
elsewhere, unlike the boot-time probe.) The output from when it finds
a card will look something like:
______________________________________________________________________
Checking the ethercard at 0x300.
Register 0x0d (0x30d) is 00
Passed initial NE2000 probe, value 00.
8390 registers: 0a 00 00 00 63 00 00 00 01 00 30 01 00 00 00 00
SA PROM 0: 00 00 00 00 c0 c0 b0 b0 05 05 65 65 05 05 20 20
SA PROM 0x10: 00 00 07 07 0d 0d 01 01 14 14 02 02 57 57 57 57
NE2000 found at 0x300, using start page 0x40 and end page 0x80.
______________________________________________________________________
Your register values and PROM values will probably be different. Note
that all the PROM values are doubled for a 16 bit card, and that the
ethernet address (00:00:c0:b0:05:65) appears in the first row, and the
double 0x57 signature appears at the end of the PROM.
The output from when there is no card installed at 0x300 will look
something like this:
______________________________________________________________________
Checking the ethercard at 0x300.
Register 0x0d (0x30d) is ff
Failed initial NE2000 probe, value ff.
8390 registers: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
SA PROM 0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
SA PROM 0x10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Invalid signature found, wordlength 2.
______________________________________________________________________
The 0xff values arise because that is the value that is returned when
one reads a vacant i/o port. If you happen to have some other hardware
in the region that is probed, you may see some non 0xff values as
well.
7) Try warm booting into linux from a DOS boot floppy (via loadlin)
after running the supplied DOS driver or config program. It may be
doing some extra (i.e. non-standard) "magic" to initialize the card.
8) Try Russ Nelson's ne2000.com packet driver to see if even it can
see your card -- if not, then things do not look good. Example:
A:> ne2000 0x60 10 0x300
The arguments are software interrupt vector, hardware IRQ, and i/o
base. You can get it from any msdos archive in pktdrv11.zip -- The
current version may be newer than 11.
3.5. Problems with SMC Ultra/EtherEZ and WD80*3 cards
Problem: You get messages such as the following:
eth0: bogus packet size: 65531, status=0xff, nxpg=0xff
Reason: There is a shared memory problem.
Solution: The most common reason for this is PCI machines that are not
configured to map in ISA memory devices. Hence you end up reading the
PC's RAM (all 0xff values) instead of the RAM on the card that
contains the data from the received packet.
Other typical problems that are easy to fix are board conflicts,
having cache or `shadow ROM' enabled for that region, or running your
ISA bus faster than 8Mhz. There are also a surprising number of memory
failures on ethernet cards, so run a diagnostic program if you have
one for your ethercard.
Problem: SMC EtherEZ doesn't work in non-shared memory (PIO) mode.
Reason: Older versions of the Ultra driver only supported the card in
the shared memory mode of operation.
Solution: The driver in kernel version 2.0 and above also supports the
programmed i/o mode of operation. Upgrade to v2.0, or get the drop-in
replacement for kernel v1.2.13 from Donald's ftp/www site.
Problem: Old wd8003 and/or jumper-settable wd8013 always get the IRQ
wrong.
Reason: The old wd8003 cards and jumper-settable wd8013 clones don't
have the EEPROM that the driver can read the IRQ setting from. If the
driver can't read the IRQ, then it tries to auto-IRQ to find out what
it is. And if auto-IRQ returns zero, then the driver just assigns IRQ
5 for an 8 bit card or IRQ 10 for a 16 bit card.
Solution: Avoid the auto-IRQ code, and tell the kernel what the IRQ
that you have jumpered the card to is via a boot time argument. For
example, if you are using IRQ 9, using the following should work.
LILO: linux ether=9,0,eth0
Problem: SMC Ultra card is detected as wd8013, but the IRQ and shared
memory base is wrong.
Reason: The Ultra card looks a lot like a wd8013, and if the Ultra
driver is not present in the kernel, the wd driver may mistake the
ultra as a wd8013. The ultra probe comes before the wd probe, so this
usually shouldn't happen. The ultra stores the IRQ and mem base in the
EEPROM differently than a wd8013, hence the bogus values reported.
Solution: Recompile with only the drivers you need in the kernel. If
you have a mix of wd and ultra cards in one machine, and are using
modules, then load the ultra module first.
3.6. Problems with 3Com cards
Problem: The 3c503 picks IRQ N, but this is needed for some other
device which needs IRQ N. (eg. CD ROM driver, modem, etc.) Can this
be fixed without compiling this into the kernel?
Solution: The 3c503 driver probes for a free IRQ line in the order {5,
9/2, 3, 4}, and it should pick a line which isn't being used. The
driver chooses when the card is ifconfig'ed into operation.
If you are using a modular driver, you can use module parameters to
set various things, including the IRQ value.
The following selects IRQ9, base location 0x300, , and
if_port #1 (the external transceiver).
io=0x300 irq=9 xcvr=1
Alternately, if the driver is compiled into the kernel, you can set
the same values at boot by passing parameters via LILO.
LILO: linux ether=9,0x300,0,1,eth0
The following selects IRQ3, probes for the base location, , and the default if_port #0 (the internal transceiver)
LILO: linux ether=3,0,0,0,eth0
Problem: 3c503: configured interrupt X invalid, will use autoIRQ.
Reason: The 3c503 card can only use one of IRQ{5, 2/9, 3, 4} (These
are the only lines that are connected to the card.) If you pass in an
IRQ value that is not in the above set, you will get the above
message. Usually, specifying an interrupt value for the 3c503 is not
necessary. The 3c503 will autoIRQ when it gets ifconfig'ed, and pick
one of IRQ{5, 2/9, 3, 4}.
Solution: Use one of the valid IRQs listed above, or enable autoIRQ by
not specifying the IRQ line at all.
Problem: The supplied 3c503 drivers don't use the AUI (thicknet) port.
How does one choose it over the default thinnet port?
Solution: The 3c503 AUI port can be selected at boot-time for in-
kernel drivers, and at module insertion for modular drivers. The
selection is overloaded onto the low bit of the currently-unused
dev->rmem_start variable, so a boot-time parameter of:
LILO: linux ether=0,0,0,1,eth0
should work for in-kernel drivers.
To specify the AUI port when loading as a module, just append xcvr=1
to the module options line along with your i/o and irq values.
3.7. FAQs Not Specific to Any Card.
3.7.1. Ethercard is Not Detected at Boot.
The usual reason for this is that people are using a kernel that does
not have support for their particular card built in. For a modular
kernel, it usually means that the required module has not been
requested for loading, or that an I/O address needs to be specified as
a module option.
If you are using a modular based kernel, such as those installed by
most of the linux distributions, then try and use the configuration
utility for the distribution to select the module for your card. For
ISA cards, it is a good idea to determine the I/O address of the card
and add it as an option (e.g. io=0x340) if the configuration utility
asks for any options. If there is no configuration utility, then you
will have to add the correct module name (and options) to
/etc/conf.modules -- see man modprobe for more details.
If you are using a pre-compiled kernel that is part of a distribution
set, then check the documentation to see which kernel you installed,
and if it was built with support for your particular card. If it
wasn't, then your options are to try and get one that has support for
your card, or build your own.
It is usually wise to build your own kernel with only the drivers you
need, as this cuts down on the kernel size (saving your precious RAM
for applications!) and reduces the number of device probes that can
upset sensitive hardware. Building a kernel is not as complicated as
it sounds. You just have to answer yes or no to a bunch of questions
about what drivers you want, and it does the rest.
The next main cause is having another device using part of the i/o
space that your card needs. Most cards are 16 or 32 bytes wide in i/o
space. If your card is set at 0x300 and 32 bytes wide, then the driver
will ask for 0x300-0x31f. If any other device driver has registered
even one port anywhere in that range, the probe will not take place at
that address and the driver will silently continue to the next of the
probed addresses. So, after booting, do a cat /proc/ioports and verify
that the full iospace that the card will require is vacant.
Another problem is having your card jumpered to an i/o address that
isn't probed by default. There is a list ``probed addresses'' for each
card in this document. Even if the i/o setting of your card is not in
the list of probed addresses, you can supply it at boot (for in-kernel
drivers) with the ether= command as described in ``Passing Ethernet
Arguments...'' Modular drivers can make use of the io= option to
specify an address that isn't probed by default.
3.7.2. ifconfig reports the wrong i/o address for the card.
No it doesn't. You are just interpreting it incorrectly. This is not
a bug, and the numbers reported are correct. It just happens that some
8390 based cards (wd80x3, smc-ultra, etc) have the actual 8390 chip
living at an offset from the first assigned i/o port. This is the
value stored in dev->base_addr, and is what ifconfig reports. If you
want to see the full range of ports that your card uses, then try cat
/proc/ioports which will give the numbers you expect.
3.7.3. PCI machine detects card but driver fails probe.
Newer PCI BIOSes may not enable all PCI cards at power-up, especially
if the BIOS option `PNP OS' is enabled. This mis-feature is to support
the next release of Windows which still uses some real-mode drivers.
Either disable this option, or try and upgrade to a newer driver which
has the code to enable a disabled card.
3.7.4. Shared Memory ISA cards in PCI Machine dont work (0xffff)
This will usually show up as reads of lots of 0xffff values. No
shared memory cards of any type will work in a PCI machine unless you
have the PCI ROM BIOS/CMOS SETUP configuration set properly. You have
to set it to allow shared memory access from the ISA bus for the
memory region that your card is trying to use. If you can't figure out
which settings are applicable then ask your supplier or local computer
guru. For AMI BIOS, there is usually a "Plug and Play" section where
there will be an ``ISA Shared Memory Size'' and ``ISA Shared Memory
Base'' settings. For cards like the wd8013 and SMC Ultra, change the
size from the default of `Disabled' to 16kB, and change the base to
the shared memory address of your card.
3.7.5. NexGen machine gets `mismatched read page pointers' errors.
A quirk of the NexGen CPU caused all users with 8390 based cards
(wd80x3, 3c503, SMC Ultra/EtherEZ, ne2000, etc.) to get these error
messages. Kernel versions 2.0 and above do not have these problems.
Upgrade your kernel.
3.7.6. Asynchronous Transfer Mode (ATM) Support
Werner Almesberger has been working on ATM support for linux. He has
been working with the Efficient Networks ENI155p board (Efficient
Networks ) and the Zeitnet ZN1221 board
(Zeitnet ).
Werner says that the driver for the ENI155p is rather stable, while
the driver for the ZN1221 is presently unfinished.
Check the latest/updated status at the following URL:
Linux ATM Support
3.7.7. Gigabyte Ethernet Support
Is there any gigabyte ethernet support for Linux?
A driver for the Packet Engines G-NIC PCI Gigabit Ethernet adapter is
due to be added into the upcoming release of kernel v2.0.34. For more
details, support, and driver updates, see:
http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html
3.7.8. FDDI Support
Is there FDDI support for Linux?
Yes. Larry Stefani has written a driver for v2.0 with Digital's DEFEA
(FDDI EISA) and DEFPA (FDDI PCI) cards. This was included into the
v2.0.24 kernel. Currently no other cards are supported though.
3.7.9. Full Duplex Support
Will Full Duplex give me 20MBps? Does Linux support it?
Cameron Spitzer writes the following about full duplex 10Base-T cards:
``If you connect it to a full duplex switched hub, and your system is
fast enough and not doing much else, it can keep the link busy in both
directions. There is no such thing as full duplex 10BASE-2 or
10BASE-5 (thin and thick coax). Full Duplex works by disabling
collision detection in the adapter. That's why you can't do it with
coax; the LAN won't run that way. 10BASE-T (RJ45 interface) uses
separate wires for send and receive, so it's possible to run both ways
at the same time. The switching hub takes care of the collision
problem. The signalling rate is 10 Mbps.''
So as you can see, you still will only be able to receive or transmit
at 10Mbps, and hence don't expect a 2x performance increase. As to
whether it is supported or not, that depends on the card and possibly
the driver. Some cards may do auto-negotiation, some may need driver
support, and some may need the user to select an option in a card's
EEPROM configuration. Only the serious/heavy user would notice the
difference between the two modes anyway.
3.7.10. Ethernet Cards for Linux on Alpha/AXP PCI Boards
As of v2.0, only the 3c509, depca, de4x5 lance32, and all the 8390
drivers (wd, smc-ultra, ne, 3c503, etc.) have been made `architecture
independent' so as to work on the DEC Alpha CPU based systems. Other
updated PCI drivers from Donald's WWW page may also work as these have
been written with architecture independence in mind.
Note that the changes that are required to make a driver architecture
independent aren't that complicated. You only need to do the
following:
-multiply all jiffies related values by HZ/100 to account for the
different HZ value that the Alpha uses. (i.e timeout=2; becomes
timeout=2*HZ/100;)
-replace any i/o memory (640k to 1MB) pointer dereferences with the
appropriate readb() writeb() readl() writel() calls, as shown in this
example.
______________________________________________________________________
- int *mem_base = (int *)dev->mem_start;
- mem_base[0] = 0xba5eba5e;
+ unsigned long mem_base = dev->mem_start;
+ writel(0xba5eba5e, mem_base);
______________________________________________________________________
-replace all memcpy() calls that have i/o memory as source or target
destinations with the appropriate one of memcpy_fromio() or
memcpy_toio().
Details on handling memory accesses in an architecture independent
fashion are documented in the file linux/Documentation/IO-mapping.txt
that comes with recent kernels.
3.7.11. Ethernet for Linux on SUN/Sparc Hardware.
For the most up to date information on Sparc stuff, try the following
URL:
Linux Sparc
Note that some Sparc ethernet hardware gets its MAC address from the
host computer, and hence you can end up with multiple interfaces all
with the same MAC address. If you need to put more than one interface
on the same net then use the hw option to ifconfig to assign unique
MAC address.
Issues regarding porting PCI drivers to the Sparc platform are similar
to those mentioned above for the AXP platform. In addition there may
be some endian issues, as the Sparc is big endian, and the AXP and
ix86 are little endian.
3.7.12. Linking 10BaseT without a Hub
Can I link 10BaseT (RJ45) based systems together without a hub?
You can link 2 machines easily, but no more than that, without extra
devices/gizmos. See ``Twisted Pair'' -- it explains how to do it. And
no, you can't hack together a hub just by crossing a few wires and
stuff. It's pretty much impossible to do the collision signal right
without duplicating a hub.
3.7.13. SIOCSIFxxx: No such device
I get a bunch of `SIOCSIFxxx: No such device' messages at boot,
followed by a `SIOCADDRT: Network is unreachable' What is wrong?
Your ethernet device was not detected at boot/module insertion time,
and when ifconfig and route are run, they have no device to work with.
Use dmesg | more to review the boot messages and see if there are any
messages about detecting an ethernet card.
3.7.14. SIOCSFFLAGS: Try again
I get `SIOCSFFLAGS: Try again' when I run `ifconfig' -- Huh?
Some other device has taken the IRQ that your ethercard is trying to
use, and so the ethercard can't use the IRQ. You don't necessairly
need to reboot to resolve this, as some devices only grab the IRQs
when they need them and then release them when they are done. Examples
are some sound cards, serial ports, floppy disk driver, etc. You can
type cat /proc/interrupts to see which interrupts are presently in
use. Most of the Linux ethercard drivers only grab the IRQ when they
are opened for use via `ifconfig'. If you can get the other device to
`let go' of the required IRQ line, then you should be able to `Try
again' with ifconfig.
3.7.15. Using `ifconfig' and Link UNSPEC with HW-addr of
00:00:00:00:00:00
When I run ifconfig with no arguments, it reports that LINK is UNSPEC
(instead of 10Mbs Ethernet) and it also says that my hardware address
is all zeros.
This is because people are running a newer version of the `ifconfig'
program than their kernel version. This new version of ifconfig is not
able to report these properties when used in conjunction with an older
kernel. You can either upgrade your kernel, `downgrade' ifconfig, or
simply ignore it. The kernel knows your hardware address, so it really
doesn't matter if ifconfig can't read it.
You may also get strange information if the ifconfig program you are
using is a lot older than the kernel you are using.
3.7.16. Huge Number of RX and TX Errors
When I run ifconfig with no arguments, it reports that I have a huge
error count in both rec'd and transmitted packets. It all seems to
work ok -- What is wrong?
Look again. It says RX packets big number PAUSE errors 0 PAUSE dropped
0 PAUSE overrun 0. And the same for the TX column. Hence the big
numbers you are seeing are the total number of packets that your
machine has rec'd and transmitted. If you still find it confusing,
try typing cat /proc/net/dev instead.
3.7.17. Entries in /dev/ for Ethercards
I have /dev/eth0 as a link to /dev/xxx. Is this right?
Contrary to what you have heard, the files in /dev/* are not used.
You can delete any /dev/wd0, /dev/ne0 and similar entries.
3.7.18. Linux and ``trailers''
Should I disable trailers when I `ifconfig' my ethercard?
You can't disable trailers, and you shouldn't want to. `Trailers' are
a hack to avoid data copying in the networking layers. The idea was to
use a trivial fixed-size header of size `H', put the variable-size
header info at the end of the packet, and allocate all packets `H'
bytes before the start of a page. While it was a good idea, it turned
out to not work well in practice. If someone suggests the use of
`-trailers', note that it is the equivalent of sacrificial goats
blood. It won't do anything to solve the problem, but if problem fixes
itself then someone can claim deep magical knowledge.
3.7.19. Access to the raw Ethernet Device
How do I get access to the raw ethernet device in linux, without going
through TCP/IP and friends?
______________________________________________________________________
int s=socket(AF_INET,SOCK_PACKET,htons(ETH_P_ALL));
______________________________________________________________________
This gives you a socket receiving every protocol type. Do recvfrom()
calls to it and it will fill the sockaddr with device type in
sa_family and the device name in the sa_data array. I don't know who
originally invented SOCK_PACKET for Linux (its been in for ages) but
its superb stuff. You can use it to send stuff raw too via sendto()
calls. You have to have root access to do either of course.
4. Performance Tips
Here are some tips that you can use if you are suffering from low
ethernet throughput, or to gain a bit more speed on those ftp
transfers.
The ttcp.c program is a good test for measuring raw throughput speed.
Another common trick is to do a ftp> get large_file /dev/null where
large_file is > 1MB and residing in the buffer cache on the Tx'ing
machine. (Do the `get' at least twice, as the first time will be
priming the buffer cache on the Tx'ing machine.) You want the file in
the buffer cache because you are not interested in combining the file
access speed from the disk into your measurement. Which is also why
you send the incoming data to /dev/null instead of onto the disk.
4.1. General Concepts
Even an 8 bit card is able to receive back-to-back packets without any
problems. The difficulty arises when the computer doesn't get the Rx'd
packets off the card quick enough to make room for more incoming
packets. If the computer does not quickly clear the card's memory of
the packets already received, the card will have no place to put the
new packet.
In this case the card either drops the new packet, or writes over top
of a previously received packet. Either one seriously interrupts the
smooth flow of traffic by causing/requesting re-transmissions and can
seriously degrade performance by up to a factor of 5!
Cards with more onboard memory are able to ``buffer'' more packets,
and thus can handle larger bursts of back-to-back packets without
dropping packets. This in turn means that the card does not require
as low a latency from the the host computer with respect to pulling
the packets out of the buffer to avoid dropping packets.
Most 8 bit cards have an 8kB buffer, and most 16 bit cards have a 16kB
buffer. Most Linux drivers will reserve 3kB of that buffer (for two Tx
buffers), leaving only 5kB of receive space for an 8 bit card. This is
room enough for only three full sized (1500 bytes) ethernet packets.
4.2. ISA Bus Speed
As mentioned above, if the packets are removed from the card fast
enough, then a drop/overrun condition won't occur even when the amount
of Rx packet buffer memory is small. The factor that sets the rate at
which packets are removed from the card to the computer's memory is
the speed of the data path that joins the two -- that being the ISA
bus speed. (If the CPU is a dog-slow 386sx-16, then this will also
play a role.)
The recommended ISA bus clock is about 8MHz, but many motherboards and
peripheral devices can be run at higher frequencies. The clock
frequency for the ISA bus can usually be set in the CMOS setup, by
selecting a divisor of the mainboard/CPU clock frequency.
For example, here are some receive speeds as measured by the TTCP
program on a 40MHz 486, with an 8 bit WD8003EP card, for different
ISA bus speeds.
______________________________________________________________________
ISA Bus Speed (MHz) Rx TTCP (kB/s)
------------------- --------------
6.7 740
13.4 970
20.0 1030
26.7 1075
______________________________________________________________________
You would be hard pressed to do better than 1075kB/s with any 10Mb/s
ethernet card, using TCP/IP. However, don't expect every system to
work at fast ISA bus speeds. Most systems will not function properly
at speeds above 13MHz. (Also, some PCI systems have the ISA bus speed
fixed at 8MHz, so that the end user does not have the option of
increasing it.)
In addition to faster transfer speeds, one will usually also benefit
from a reduction in CPU usage due to the shorter duration memory and
i/o cycles. (Note that hard disks and video cards located on the ISA
bus will also usually experience a performance increase from an
increased ISA bus speed.)
Be sure to back up your data prior to experimenting with ISA bus
speeds in excess of 8MHz, and thouroughly test that all ISA
peripherals are operating properly after making any speed increases.
4.3. Setting the TCP Rx Window
Once again, cards with small amounts of onboard RAM and relatively
slow data paths between the card and the computer's memory run into
trouble. The default TCP Rx window setting is 32kB, which means that a
fast computer on the same subnet as you can dump 32k of data on you
without stopping to see if you received any of it okay.
Recent versions of the route command have the ability to set the size
of this window on the fly. Usually it is only for the local net that
this window must be reduced, as computers that are behind a couple of
routers or gateways are `buffered' enough to not pose a problem. An
example usage would be:
______________________________________________________________________
route add ... window
______________________________________________________________________
where win_size is the size of the window you wish to use (in bytes).
An 8 bit 3c503 card on an ISA bus operating at a speed of 8MHz or less
would work well with a window size of about 4kB. Too large a window
will cause overruns and dropped packets, and a drastic reduction in
ethernet throughput. You can check the operating status by doing a cat
/proc/net/dev which will display any dropped or overrun conditions
that occurred.
4.4. Increasing NFS performance
Some people have found that using 8 bit cards in NFS clients causes
poorer than expected performance, when using 8kB (native Sun) NFS
packet size.
The possible reason for this could be due to the difference in on
board buffer size between the 8 bit and the 16 bit cards. The maximum
ethernet packet size is about 1500 bytes. Now that 8kB NFS packet will
arrive as about 6 back to back maximum size ethernet packets. Both the
8 and 16 bit cards have no problem Rx'ing back to back packets. The
problem arises when the machine doesn't remove the packets from the
cards buffer in time, and the buffer overflows. The fact that 8 bit
cards take an extra ISA bus cycle per transfer doesn't help either.
What you can do if you have an 8 bit card is either set the NFS
transfer size to 2kB (or even 1kB), or try increasing the ISA bus
speed in order to get the card's buffer cleared out faster. I have
found that an old WD8003E card at 8MHz (with no other system load) can
keep up with a large receive at 2kB NFS size, but not at 4kB, where
performance was degraded by a factor of three.
5. Vendor/Manufacturer/Model Specific Information
The following lists many cards in alphabetical order by vendor name
and then product identifier. Beside each product ID, you will see
either `Supported', `Semi-Supported' or `Not Supported'.
Supported means that a driver for that card exists, and many people
are happily using it and it seems quite reliable.
Semi-Supported means that a driver exists, but at least one of the
following descriptions is true: (1) The driver and/or hardware are
buggy, which may cause poor performance, failing connections or even
crashes. (2) The driver is new or the card is fairly uncommon, and
hence the driver has seen very little use/testing and the driver
author has had very little feedback. Obviously (2) is preferable to
(1), and the individual description of the card/driver should make it
clear which one holds true. In either case, you will probably have to
answer `Y' when asked ``Prompt for development and/or incomplete
code/drivers?'' when running make config.
Not Supported means there is not a driver currently available for that
card. This could be due to a lack of interest in hardware that is
rare/uncommon, or because the vendors won't release the hardware
documentation required to write a driver.
Note that the difference between `Supported' and `Semi-Supported' is
rather subjective, and is based on user feedback observed in newsgroup
postings and mailing list messages. (After all, it is impossible for
one person to test all drivers with all cards for each kernel
version!!!) So be warned that you may find a card listed as semi-
supported works perfectly for you (which is great), or that a card
listed as supported gives you no end of troubles and problems (which
is not so great).
5.1. 3Com
If you are not sure what your card is, but you think it is a 3Com
card, you can probably figure it out from the assembly number. 3Com
has a document `Identifying 3Com Adapters By Assembly Number' (ref
24500002) that would most likely clear things up. See ``Technical
Information from 3Com'' for info on how to get documents from 3Com.
Also note that 3Com has a FTP site with various goodies: ftp.3Com.com
that you may want to check out.
For those of you browsing this document by a WWW browser, you can try
3Com's WWW site as well.
5.1.1. 3c501
Status -- Semi-Supported
Too brain-damaged to use. Available surplus from many places. Avoid it
like the plague. Again, do not purchase this card, even as a joke.
It's performance is horrible, and it breaks in many ways.
For those not yet convinced, the 3c501 can only do one thing at a time
-- while you are removing one packet from the single-packet buffer it
cannot receive another packet, nor can it receive a packet while
loading a transmit packet. This was fine for a network between two
8088-based computers where processing each packet and replying took
10's of msecs, but modern networks send back-to-back packets for
almost every transaction.
AutoIRQ works, DMA isn't used, the autoprobe only looks at 0x280 and
0x300, and the debug level is set with the third boot-time argument.
Once again, the use of a 3c501 is strongly discouraged! Even more so
with a IP multicast kernel, as you will grind to a halt while
listening to all multicast packets. See the comments at the top of the
source code for more details.
5.1.2. EtherLink II, 3c503, 3c503/16
Status -- Supported
The 3c503 does not have ``EEPROM setup'', so a diagnostic/setup
program isn't needed before running the card with Linux. The shared
memory address of the 3c503 is set using jumpers that are shared with
the boot PROM address. This is confusing to people familiar with other
ISA cards, where you always leave the jumper set to ``disable'' unless
you have a boot PROM.
These cards should be about the same speed as the same bus width
WD80x3, but turn out to be actually a bit slower. These shared-memory
ethercards also have a programmed I/O mode that doesn't use the 8390
facilities (their engineers found too many bugs!) The Linux 3c503
driver can also work with the 3c503 in programmed-I/O mode, but this
is slower and less reliable than shared memory mode. Also, programmed-
I/O mode is not as well tested when updating the drivers. You
shouldn't use the programmed-I/O mode unless you need it for MS-DOS
compatibility.
The 3c503's IRQ line is set in software, with no hints from an EEPROM.
Unlike the MS-DOS drivers, the Linux driver has capability to autoIRQ:
it uses the first available IRQ line in {5,2/9,3,4}, selected each
time the card is ifconfig'ed. (Older driver versions selected the IRQ
at boot time.) The ioctl() call in `ifconfig' will return EAGAIN if no
IRQ line is available at that time.
Some common problems that people have with the 503 are discussed in
``Problems with...''.
If you intend on using this driver as a loadable module you should
probably see ``Using the Ethernet Drivers as Modules'' for module
specific information.
Note that some old diskless 386 workstations have an on board 3c503
(made by 3Com and sold under different names, like `Bull') but the
vendor ID is not a 3Com ID and so it won't be detected. More details
can be found in the Etherboot package, which you will need anyways to
boot these diskless boxes.
5.1.3. 3c505
Status -- Semi-Supported
This is a driver that was written by Craig Southeren
geoffw@extro.ucc.su.oz.au. These cards also use the i82586 chip.
There are not that many of these cards about. It is included in the
standard kernel, but it is classed as an alpha driver. See ``Alpha
Drivers'' for important information on using alpha-test ethernet
drivers with Linux.
There is also the file /usr/src/linux/drivers/net/README.3c505 that
you should read if you are going to use one of these cards. It
contains various options that you can enable/disable. Technical
information is available in ``Programming the Intel chips''.
5.1.4. 3c507
Status -- Semi-Supported
This card uses one of the Intel chips, and the development of the
driver is closely related to the development of the Intel Ether
Express driver. The driver is included in the standard kernel
release, but as an alpha driver.
See ``Alpha Drivers'' for important information on using alpha-test
ethernet drivers with Linux. Technical information is available in
``Programming the Intel chips''.
5.1.5. 3c509 / 3c509B
Status -- Supported
This card is fairly inexpensive and has good performance for a non-
bus-master design. The drawbacks are that the original 3c509 requires
very low interrupt latency. The 3c509B shouldn't suffer from the same
problem, due to having a larger buffer. (See below.) These cards use
PIO transfers, similar to a ne2000 card, and so a shared memory card
such as a wd8013 will be more efficient in comparison.
The original 3c509 has a small packet buffer (4kB total, 2kB Rx, 2kB
Tx), causing the driver to occasionally drop a packet if interrupts
are masked for too long. To minimize this problem, you can try
unmasking interrupts during IDE disk transfers (see man hdparm) and/or
increasing your ISA bus speed so IDE transfers finish sooner.
The newer model 3c509B has 8kB on board, and the buffer can be split
4/4, 5/3 or 6/2 for Rx/Tx. This setting is changed with the DOS
configuration utility, and is stored on the EEPROM. This should
alleviate the above problem with the original 3c509.
3c509B users should use the supplied DOS utility to disable the plug
and play support, and to set the output media to what they require.
The linux driver currently does not support the Autodetect media
setting, so you have to select 10Base-T or 10Base-2 or AUI.
With regards to the media detection features, Cameron said:
``Autoselect is a feature of the commercial drivers for 3C509(B).
AFAIK nobody ever claimed the Linux driver attempts it. When
drivers/net/3c509.c recognizes my 3C509B at boot time, it says: eth0:
3c509 at 0x300 tag 1, 10baseT port, ... revealing that the card is
configured for 10BASE-T. It finds that out by reading the little
EEPROM, which IMHO is the Right Way To Do It.''
As for the plug-and-pray stuff, Cameron adds: ``It was a marketing
decision to turn PnP on as a factory default setting. If it caused you
a hassle, or not, please take the time to say so when you mail in your
warranty card. The more info they have, the better decisions they can
make. Also, check with your motherboard supplier to see if you need a
BIOS upgrade.''
Note that to turn off PnP entirely, you should do a 3C5X9CFG
/PNP:DISABLE and then follow that with a hard reset to ensure that it
takes effect.
Some people ask about the ``Server or Workstation'' and ``Highest
Modem Speed'' settings presented in the DOS configuration utility.
Donald writes ``These are only hints to the drivers, and the Linux
driver does not use these parameters: it always optimizes for high
throughput rather than low latency (`Server'). Low latency was
critically important for old, non-windowed, IPX throughput. To reduce
the latency the MS-DOS driver for the 3c509 disables interrupts for
some operations, blocking serial port interrupts. Thus the need for
the `modem speed' setting. The Linux driver avoids the need to
disable interrupts for long periods by operating only on whole packets
e.g. by not starting to transmit a packet until it is completely
transferred to the card.''
Note that the ISA card detection uses a different method than most
cards. Basically, you ask the cards to respond by sending data to an
ID_PORT (port 0x100 to 0x1ff on intervals of 0x10). This detection
method means that a particular card will always get detected first in
a multiple ISA 3c509 configuration. The card with the lowest hardware
ethernet address will always end up being eth0. This shouldn't matter
to anyone, except for those people who want to assign a 6 byte
hardware address to a particular interface. If you have multiple
3c509 cards, it is best to append ether=0,0,ethN commands without the
i/o port specified (i.e. use i/o=zero) and allow the probe to sort out
which card is first. Using a non-zero i/o value will ensure that it
does not detect all your cards, so don't do it.
If this really bothers you, have a look at Donald's latest driver, as
you may be able to use a 0x3c509 value in the unused mem address
fields to order the detection to suit.
5.1.6. 3c515
Status -- Not Supported
This is 3Com's farily recent ISA 100Mbps offering, codenamed
``CorkScrew''. Donald is working on support for these cards, and it
will probably appear in the near future on his WWW driver page. The
driver will be incorporated into the 3c59x/3c90x driver, so you should
probably expect to look for it on the Vortex page:
Vortex
5.1.7. 3c523
Status -- Semi-Supported
This MCA bus card uses the i82586, and Chris Beauregard has modified
the ni52 driver to work with these cards. The driver for it can be
found in the v2.1 kernel source tree.
More details can be found on the MCA-Linux page at
http://glycerine.cetmm.uni.edu/mca/
5.1.8. 3c527
Status -- Not Supported
Yes, another MCA card. No, not too much interest in it. Better
chances with the 3c529 if you are stuck with MCA.
5.1.9. 3c529
Status -- Semi-Supported
This card actually uses the same chipset as the 3c509. Donald
actually put hooks into the 3c509 driver to check for MCA cards after
probing for EISA cards, and before probing for ISA cards. But it
hasn't evolved much further than that. Donald writes:
``I don't have access to a MCA machine (nor do I fully understand the
probing code) so I never wrote the mca_adaptor_select_mode() or
mca_adaptor_id() routines. If you can find a way to get the adaptor
I/O address that assigned at boot time, you can just hard-wire that in
place of the commented-out probe. Be sure to keep the code that reads
the IRQ, if_port, and ethernet address.''
Darrell Frappier (aa822@detroit.freenet.org) reports that you can get
the i/o address from running the PS/2 reference diskette, and once you
put that directly into the driver, it does actually work.
The required MCA probe code will probably appear in the driver in a
development kernel sometime soon, now that MCA support is in the
kernel.
More details can be found on the MCA-Linux page at
http://glycerine.cetmm.uni.edu/mca/
5.1.10. 3c562
Status -- Supported
This PCMCIA card is the combination of a 3c589B ethernet card with a
modem. The modem appears as a standard modem to the end user. The only
difficulty is getting the two separate linux drivers to share one
interrupt. There are a couple of new registers and some hardware
interrupt sharing support. You need to use a v2.0 or newer kernel
that has the support for interrupt sharing.
As a side note, the modem part of the card has been reported to be not
well documented for the end user (the manual just says `supports the
AT command set') and it may not connect as well as other name brand
modems. The recommendation is to buy a 3c589B instead, and then get a
PCMCIA modem card from a company that specializes in modems.
Thanks again to Cameron for getting a sample unit and documentation
sent off to David Hinds. Look for support in David's PCMCIA package
release.
See ``PCMCIA Support'' for more info on PCMCIA chipsets, socket
enablers, etc.
5.1.11. 3c575
Status -- Not Supported
A driver for this PCMCIA card is under development and hopefully will
be included in David's PCMCIA package within a few months.
5.1.12. 3c579
Status -- Supported
The EISA version of the 509. The current EISA version uses the same 16
bit wide chip rather than a 32 bit interface, so the performance
increase isn't stunning. Make sure the card is configured for EISA
addressing mode. Read the above 3c509 section for info on the driver.
5.1.13. 3c589 / 3c589B
Status -- Semi-Supported
Many people have been using this PCMCIA card for quite some time now.
Note that support for it is not (at present) included in the default
kernel source tree. You will also need a supported PCMCIA controller
chipset. There are drivers available on Donald's ftp site:
cesdis.gsfc.nasa.gov:/pub/linux/pcmcia/README.3c589
cesdis.gsfc.nasa.gov:/pub/linux/pcmcia/3c589.c
cesdis.gsfc.nasa.gov:/pub/linux/pcmcia/dbether.c
Or for those that are net-surfing you can try:
Don's PCMCIA Stuff
You will still need a PCMCIA socket enabler as well.
See ``PCMCIA Support'' for more info on PCMCIA chipsets, socket
enablers, etc.
The "B" in the name means the same here as it does for the 3c509 case.
5.1.14. 3c590 / 3c595
Status -- Supported
These ``Vortex'' cards are for PCI bus machines, with the '590 being
10Mbps and the '595 being 3Com's 100Mbs offering. Also note that you
can run the '595 as a '590 (i.e. in a 10Mbps mode). The driver is
included in the v2.0 kernel source, but is also continually being
updated. If you have problems with the driver in the v2.0 kernel, you
can get an updated driver from the following URL:
Vortex
Note that there are two different 3c590 cards out there, early models
that had 32kB of on-board memory, and later models that only have 8kB
of memory. Chances are you won't be able to buy a new 3c59x for much
longer, as it is being replaced with the 3c90x card. If you are buying
a used one off somebody, try and get the 32kB version. The 3c595 cards
have 64kB, as you can't get away with only 8kB RAM at 100Mbps!
A thanks to Cameron Spitzer and Terry Murphy of 3Com for sending cards
and documentation to Donald so he could write the driver.
Donald has set up a mailing list for Vortex driver support. To join
the list, just do:
echo subscribe | /bin/mail linux-vortex-request@cesdis.gsfc.nasa.gov
5.1.15. 3c592 / 3c597
Status -- Supported
These are the EISA versions of the 3c59x series of cards. The
3c592/3c597 (aka Demon) should work with the vortex driver discussed
above.
5.1.16. 3c900 / 3c905 / 3c905B
Status -- Supported
These cards (aka `Boomerang', aka EtherLink III XL) have been released
to take over the place of the 3c590/3c595 cards.
The support for the Cyclone `B' revision was only recently added. To
use this card with older v2.0 kernels, you must obtain the updated
3c59x.c driver from Donald's site at:
Vortex-Page
If in doubt about anything then check out the above WWW page. Donald
has set up a mailing list for Vortex driver support announcements and
etc. To join the list, just do:
echo subscribe | /bin/mail linux-vortex-request@cesdis.gsfc.nasa.gov
5.2. Accton
5.2.1. Accton MPX
Status -- Supported
Don't let the name fool you. This is still supposed to be a NE2000
compatible card, and should work with the ne2000 driver.
5.2.2. Accton EN1203, EN1207, EtherDuo-PCI
Status -- Supported
This is another implementation of the DEC 21040 PCI chip. The EN1207
card has the 21140, and also has a 10Base-2 connector, which has
proved troublesome for some people in terms of selecting that media.
Using the card with 10Base-T and 100Base-T media have worked for
others though. So as with all purchases, you should try and make sure
you can return it if it doesn't work for you.
See ``DEC 21040'' for more information on these cards, and the present
driver situation.
5.2.3. Accton EN2209 Parallel Port Adaptor (EtherPocket)
Status -- Semi-Supported
A driver for these parallel port adapters is available but not yet
part of the 2.0 or 2.1 kernel source. You have to get the driver from:
http://www.unix-ag.uni-siegen.de/~nils/accton_linux.html
5.2.4. Accton EN2212 PCMCIA Card
Status -- Semi-Supported
David Hinds has been working on a driver for this card, and you are
best to check the latest release of his PCMCIA package to see what the
present status is.
5.3. Allied Telesyn/Telesis
5.3.1. AT1500
Status --Supported
These are a series of low-cost ethercards using the 79C960 version of
the AMD LANCE. These are bus-master cards, and hence one of the faster
ISA bus ethercards available.
DMA selection and chip numbering information can be found in ``AMD
LANCE''.
More technical information on AMD LANCE based Ethernet cards can be
found in ``Notes on AMD...''.
5.3.2. AT1700
Status -- Supported
Note that to access this driver during make config you still have to
answer `Y' when asked ``Prompt for development and/or incomplete
code/drivers?'' at the first. This is simply due to lack of feedback
on the driver stability due to it being a relatively rare card. This
will probably be changed for v2.1 kernels.
The Allied Telesis AT1700 series ethercards are based on the Fujitsu
MB86965. This chip uses a programmed I/O interface, and a pair of
fixed-size transmit buffers. This allows small groups of packets to be
sent back-to-back, with a short pause while switching buffers.
A unique feature is the ability to drive 150ohm STP (Shielded Twisted
Pair) cable commonly installed for Token Ring, in addition to 10baseT
100ohm UTP (unshielded twisted pair). A fibre optic version of the
card (AT1700FT) exists as well.
The Fujitsu chip used on the AT1700 has a design flaw: it can only be
fully reset by doing a power cycle of the machine. Pressing the reset
button doesn't reset the bus interface. This wouldn't be so bad,
except that it can only be reliably detected when it has been freshly
reset. The solution/work-around is to power-cycle the machine if the
kernel has a problem detecting the AT1700.
Some production runs of the AT1700 had another problem: they are
permanently wired to DMA channel 5. This is undocumented, there are
no jumpers to disable the "feature", and no driver dares use the DMA
capability because of compatibility problems. No device driver will be
written using DMA if installing a second card into the machine breaks
both, and the only way to disable the DMA is with a knife.
5.3.3. AT2450
Status -- Supported
This is the PCI version of the AT1500, and it doesn't suffer from the
problems that the Boca 79c970 PCI card does. DMA selection and chip
numbering information can be found in ``AMD LANCE''.
More technical information on AMD LANCE based Ethernet cards can be
found in ``Notes on AMD...''.
5.3.4. AT2540FX
Status -- Semi-Supported
This card uses the i82557 chip, and hence may/should work with the
eepro100 driver. If you try this please send in a report so this
information can be updated.
5.4. AMD / Advanced Micro Devices
Carl Ching of AMD was kind enough to provide a very detailed
description of all the relevant AMD ethernet products which helped
clear up this section.
5.4.1. AMD LANCE (7990, 79C960/961/961A, PCnet-ISA)
Status -- Supported
There really is no AMD ethernet card. You are probably reading this
because the only markings you could find on your card said AMD and the
above number. The 7990 is the original `LANCE' chip, but most stuff
(including this document) refer to all these similar chips as `LANCE'
chips. (...incorrectly, I might add.)
These above numbers refer to chips from AMD that are the heart of many
ethernet cards. For example, the Allied Telesis AT1500 (see
``AT1500'') and the NE1500/2100 (see ``NE1500'') use these chips.
The 7990/79c90 have long been replaced by newer versions. The 79C960
(a.k.a. PCnet-ISA) essentially contains the 79c90 core, along with all
the other hardware support required, which allows a single-chip
ethernet solution. The 79c961 (PCnet-ISA+) is a jumperless Plug and
Play version of the '960. The final chip in the ISA series is the
79c961A (PCnet-ISA II), which adds full duplex capabilities. All
cards with one of these chips should work with the lance.c driver,
with the exception of very old cards that used the original 7990 in a
shared memory configuration. These old cards can be spotted by the
lack of jumpers for a DMA channel.
One common problem people have is the `busmaster arbitration failure'
message. This is printed out when the LANCE driver can't get access to
the bus after a reasonable amount of time has elapsed (50us). This
usually indicates that the motherboard implementation of bus-mastering
DMA is broken, or some other device is hogging the bus, or there is a
DMA channel conflict. If your BIOS setup has the `GAT option' (for
Guaranteed Access Time) then try toggling/altering that setting to see
if it helps.
Also note that the driver only looks at the addresses: 0x300, 0x320,
0x340, 0x360 for a valid card, and any address supplied by an ether=
boot argument is silently ignored (this will be fixed) so make sure
your card is configured for one of the above I/O addresses for now.
The driver will still work fine, even if more than 16MB of memory is
installed, since low-memory `bounce-buffers' are used when needed
(i.e. any data from above 16MB is copied into a buffer below 16MB
before being given to the card to transmit.)
The DMA channel can be set with the low bits of the otherwise-unused
dev->mem_start value (a.k.a. PARAM_1). (see ``PARAM_1'') If unset it
is probed for by enabling each free DMA channel in turn and checking
if initialization succeeds.
The HP-J2405A board is an exception: with this board it's easy to read
the EEPROM-set values for the IRQ, and DMA.
See ``Notes on AMD...'' for more info on these chips.
5.4.2. AMD 79C965 (PCnet-32)
Status -- Supported
This is the PCnet-32 -- a 32 bit bus-master version of the original
LANCE chip for VL-bus and local bus systems. chip. While these chips
can be operated with the standard lance.c driver, a 32 bit version
(lance32.c) is also available that does not have to concern itself
with any 16MB limitations associated with the ISA bus.
5.4.3. AMD 79C970/970A (PCnet-PCI)
Status -- Supported
This is the PCnet-PCI -- similar to the PCnet-32, but designed for PCI
bus based systems. Please see the above PCnet-32 information. This
means that you need to build a kernel with PCI BIOS support enabled.
The '970A adds full duplex support along with some other features to
the original '970 design.
Note that the Boca implementation of the 79C970 fails on fast Pentium
machines. This is a hardware problem, as it affects DOS users as well.
See the Boca section for more details.
5.4.4. AMD 79C971 (PCnet-FAST)
Status -- Supported
This is AMD's 100Mbit chip for PCI systems, which also supports full
duplex operation. It was introduced in June 1996.
5.4.5. AMD 79C974 (PCnet-SCSI)
Status -- Supported
This is the PCnet-SCSI -- which is basically treated like a '970 from
an Ethernet point of view. Also see the above information. Don't ask
if the SCSI half of the chip is supported -- this is the Ethernet-
HowTo, not the SCSI-HowTo.
5.5. Ansel Communications
5.5.1. AC3200 EISA
Status -- Semi-Supported
Note that to access this driver during make config you still have to
answer `Y' when asked ``Prompt for development and/or incomplete
code/drivers?'' at the first. This is simply due to lack of feedback
on the driver stability due to it being a relatively rare card.
This driver is included in the present kernel as an alpha test driver.
It is based on the common NS8390 chip used in the ne2000 and wd80x3
cards. Please see ``Alpha Drivers'' in this document for important
information regarding alpha drivers.
If you use it, let one of us know how things work out, as feedback has
been low, even though the driver has been in the kernel since v1.1.25.
If you intend on using this driver as a loadable module you should
probably see ``Using the Ethernet Drivers as Modules'' for module
specific information.
5.6. Apricot
5.6.1. Apricot Xen-II On Board Ethernet
Status -- Supported
This on board ethernet uses an i82596 bus-master chip. It can only be
at i/o address 0x300. The author of this driver is Mark Evans. By
looking at the driver source, it appears that the IRQ is hardwired to
10.
Earlier versions of the driver had a tendency to think that anything
living at 0x300 was an apricot NIC. Since then the hardware address
is checked to avoid these false detections.
5.7. Arcnet
Status -- Supported
With the very low cost and better performance of ethernet, chances are
that most places will be giving away their Arcnet hardware for free,
resulting in a lot of home systems with Arcnet.
An advantage of Arcnet is that all of the cards have identical
interfaces, so one driver will work for everyone. It also has built in
error handling so that it supposedly never loses a packet. (Great for
UDP traffic!)
Avery Pennarun's arcnet driver has been in the default kernel sources
since 1.1.80. The arcnet driver uses `arc0' as its name instead of the
usual `eth0' for ethernet devices. Bug reports and success stories
can be mailed to:
apenwarr@foxnet.net
There are information files contained in the standard kernel for
setting jumpers and general hints.
Supposedly the driver also works with the 100Mbs ARCnet cards as well!
5.8. AT&T
Note that AT&T's StarLAN is an orphaned technology, like SynOptics
LattisNet, and can't be used in a standard 10Base-T environment,
without a hub that `speaks' both.
5.8.1. AT&T T7231 (LanPACER+)
Status -- Not Supported
These StarLAN cards use an interface similar to the i82586 chip. At
one point, Matthijs Melchior (matthijs.n.melchior@att.com) was playing
with the 3c507 driver, and almost had something useable working.
Haven't heard much since that.
5.9. AT-Lan-Tec / RealTek
5.9.1. AT-Lan-Tec / RealTek Pocket adaptor
Status -- Supported
This is a generic, low-cost OEM pocket adaptor being sold by AT-Lan-
Tec, and (likely) a number of other suppliers. A driver for it is
included in the standard kernel. Note that there is substantial
information contained in the driver source file `atp.c'.
Note that the device name that you pass to ifconfig is not eth0 but
atp0 for this device.
5.9.2. RealTek 8009
Status -- Supported
This is an ISA NE2000 clone, and is reported to work fine with the
linux NE2000 driver. The rset8009.exe program can be obtained from
RealTek's WWW site at http://www.realtek.com.tw - or via ftp from the
same site.
5.9.3. RealTek 8019
Status -- Supported
This is a Plug and Pray version of the above. Use the DOS software to
disable PnP and enable jumperless configuration; set the card to a
sensible i/o address and IRQ and you should be ready to go. (If using
the driver as a module, don't forget to add an io=0xNNN option to
/etc/conf.modules). The rset8019.exe program can be obtained from
RealTek's WWW site at http://www.realtek.com.tw - or via ftp from the
same site.
5.9.4. RealTek 8029
Status -- Supported
This is a PCI single chip implementation of a NE2000 clone. Various
vendors are now selling cards with this chip. See ``NE2000-PCI'' for
information on using any of these cards.
5.9.5. RealTek 8129/8139
Status -- Semi-Supported
Another PCI single chip ethernet solution from RealTek. A driver for
cards based upon this chip is due to be included in the v2.0.34
release of linux. For more information, see:
http://cesdis.gsfc.nasa.gov/linux/drivers/rtl8139.html
5.10. Boca Research
Yes, they make more than just multi-port serial cards. :-)
5.10.1. Boca BEN (ISA, VLB, PCI)
Status -- Supported
These cards are based on AMD's PCnet chips. Perspective buyers should
be warned that many users have had endless problems with these VLB/PCI
cards. Owners of fast Pentium systems have been especially hit. Note
that this is not a driver problem, as it hits DOS/Win/NT users as
well. Boca's technical support number is (407) 241-8088, and you can
also reach them at 75300.2672@compuserve.com. The older ISA cards
don't appear to suffer the same problems.
Donald did a comparitive test with a Boca PCI card and a similar
Allied Telsyn PCnet/PCI implementation, which showed that the problem
lies in Boca's implementation of the PCnet/PCI chip. These test
results can be accessed on Don's www server.
Linux at CESDIS
Boca is offering a `warranty repair' for affected owners, which
involves adding one of the missing capacitors, but it appears that
this fix doesn't work 100 percent for most people, although it helps
some.
If you are still thinking of buying one of these cards, then at least
try and get a 7 day unconditional return policy, so that if it doesn't
work properly in your system, you can return it.
More general information on the AMD chips can be found in ``AMD
LANCE''.
More technical information on AMD LANCE based Ethernet cards can be
found in ``Notes on AMD...''.
5.11. Cabletron
Donald writes: `Yes, another one of these companies that won't release
its programming information. They waited for months before actually
confirming that all their information was proprietary, deliberately
wasting my time. Avoid their cards like the plague if you can. Also
note that some people have phoned Cabletron, and have been told things
like `a D. Becker is working on a driver for linux' -- making it sound
like I work for them. This is NOT the case.'
Apparently Cabletron has changed their policy with respect to
programming information (like Xircom) since Donald made the above
comment several years ago -- send e-mail to support@ctron.com if you
want to verify this or ask for programming information. However, at
this point in time, there is little demand for modified/updated
drivers for the older E20xx and E21xx cards.
5.11.1. E10**, E10**-x, E20**, E20**-x
Status -- Semi-Supported
These are NEx000 almost-clones that are reported to work with the
standard NEx000 drivers, thanks to a ctron-specific check during the
probe. If there are any problems, they are unlikely to be fixed, as
the programming information is unavailable.
5.11.2. E2100
Status -- Semi-Supported
Again, there is not much one can do when the programming information
is proprietary. The E2100 is a poor design. Whenever it maps its
shared memory in during a packet transfer, it maps it into the whole
128K region! That means you can't safely use another interrupt-driven
shared memory device in that region, including another E2100. It will
work most of the time, but every once in a while it will bite you.
(Yes, this problem can be avoided by turning off interrupts while
transferring packets, but that will almost certainly lose clock
ticks.) Also, if you mis-program the board, or halt the machine at
just the wrong moment, even the reset button won't bring it back. You
will have to turn it off and leave it off for about 30 seconds.
Media selection is automatic, but you can override this with the low
bits of the dev->mem_end parameter. See ``PARAM_2''. Module users can
specify an xcvr=N value as an option in the /etc/conf.modules file.
Also, don't confuse the E2100 for a NE2100 clone. The E2100 is a
shared memory NatSemi DP8390 design, roughly similar to a brain-
damaged WD8013, whereas the NE2100 (and NE1500) use a bus-mastering
AMD LANCE design.
There is an E2100 driver included in the standard kernel. However,
seeing as programming info isn't available, don't expect bug-fixes.
Don't use one unless you are already stuck with the card.
If you intend on using this driver as a loadable module you should
probably see ``Using the Ethernet Drivers as Modules'' for module
specific information.
5.11.3. E22**
Status -- Semi-Supported
According to information in a Cabletron Tech Bulletin, these cards use
the standard AMD PC-Net chipset (see ``AMD PC-Net'') and should work
with the generic lance driver.
5.12. Cogent
Here is where and how to reach them:
Cogent Data Technologies, Inc.
175 West Street, P.O. Box 926
Friday Harbour, WA 98250, USA.
Cogent Sales
15375 S.E. 30th Place, Suite 310
Bellevue, WA 98007, USA.
Technical Support:
Phone (360) 378-2929 between 8am and 5pm PST
Fax (360) 378-2882
Compuserve GO COGENT
Bulletin Board Service (360) 378-5405
Internet: support@cogentdata.com
5.12.1. EM100-ISA/EISA
Status -- Semi-Supported
These cards use the SMC 91c100 chip and may work with the SMC 91c92
driver, but this has yet to be verified.
5.12.2. Cogent eMASTER+, EM100-PCI, EM400, EM960, EM964
Status -- Supported
These are yet another DEC 21040 implementation that should hopefully
work fine with the standard 21040 driver.
The EM400 and the EM964 are four port cards using a DEC 21050 bridge
and 4 21040 chips.
See ``DEC 21040'' for more information on these cards, and the present
driver situation.
5.13. Compaq
Compaq aren't really in the business of making ethernet cards, but a
lot of their systems have embedded ethernet controllers on the
motherboard.
5.13.1. Compaq Deskpro / Compaq XL (Embedded AMD Chip)
Status -- Supported
Machines such as the XL series have an AMD 79c97x PCI chip on the
mainboard that can be used with the standard LANCE driver. But before
you can use it, you have to do some trickery to get the PCI BIOS to a
place where Linux can see it. Frank Maas was kind enough to provide
the details:
`` The problem with this Compaq machine however is that the PCI
directory is loaded in high memory, at a spot where the Linux kernel
can't (won't) reach. Result: the card is never detected nor is it
usable (sideline: the mouse won't work either) The workaround (as
described thoroughly in http://www-c724.uibk.ac.at/XL/) is to load MS-
DOS, launch a little driver Compaq wrote and then load the Linux
kernel using LOADLIN. Ok, I'll give you time to say `yuck, yuck', but
for now this is the only working solution I know of. The little driver
simply moves the PCI directory to a place where it is normally stored
(and where Linux can find it).''
More general information on the AMD chips can be found in ``AMD
LANCE''.
5.14. Danpex
5.14.1. Danpex EN9400
Status -- Supported
Yet another card based on the DEC 21040 chip, reported to work fine,
and at a relatively cheap price.
See ``DEC 21040'' for more information on these cards, and the present
driver situation.
5.15. D-Link
5.15.1. DE-100, DE-200, DE-220-T, DE-250
Status -- Supported
Some of the early D-Link cards didn't have the 0x57 PROM signature,
but the ne2000 driver knows about them. For the software configurable
cards, you can get the config program from www.dlink.com. The DE2**
cards were the most widely reported as having the spurious transfer
address mismatch errors with early versions of linux. Note that there
are also cards from Digital (DEC) that are also named DE100 and DE200,
but the similarity stops there.
5.15.2. DE-520
Status -- Supported
This is a PCI card using the PCI version of AMD's LANCE chip. DMA
selection and chip numbering information can be found in ``AMD
LANCE''.
More technical information on AMD LANCE based Ethernet cards can be
found in ``Notes on AMD...''.
5.15.3. DE-530
Status -- Supported
This is a generic DEC 21040 PCI chip implementation, and is reported
to work with the generic 21040 tulip driver.
See ``DEC 21040'' for more information on these cards, and the present
driver situation.
5.15.4. DE-600
Status -- Supported
Laptop users and other folk who might want a quick way to put their
computer onto the ethernet may want to use this. The driver is
included with the default kernel source tree. Bjorn Ekwall
bj0rn@blox.se wrote the driver. Expect about 180kb/s transfer speed
from this via the parallel port. You should read the README.DLINK file
in the kernel source tree.
Note that the device name that you pass to ifconfig is now eth0 and
not the previously used dl0.
If your parallel port is not at the standard 0x378 then you will have
to recompile. Bjorn writes: ``Since the DE-620 driver tries to sqeeze
the last microsecond from the loops, I made the irq and port address
constants instead of variables. This makes for a usable speed, but it
also means that you can't change these assignements from e.g. lilo;
you _have_ to recompile...'' Also note that some laptops implement the
on-board parallel port at 0x3bc which is where the parallel ports on
monochrome cards were/are.
5.15.5. DE-620
Status -- Supported
Same as the DE-600, only with two output formats. Bjorn has written a
driver for this model, for kernel versions 1.1 and above. See the
above information on the DE-600.
5.15.6. DE-650
Status -- Semi-Supported
Some people have been using this PCMCIA card for some time now with
their notebooks. It is a basic 8390 design, much like a NE2000. The
LinkSys PCMCIA card and the IC-Card Ethernet (available from Midwest
Micro) are supposedly DE-650 clones as well. Note that at present,
this driver is not part of the standard kernel, and so you will have
to do some patching.
See ``PCMCIA Support'' in this document, and if you can, have a look
at:
Don's PCMCIA Stuff
5.16. DFI
5.16.1. DFINET-300 and DFINET-400
Status -- Supported
These cards are now detected (as of 0.99pl15) thanks to Eberhard
Moenkeberg emoenke@gwdg.de who noted that they use `DFI' in the first
3 bytes of the prom, instead of using 0x57 in bytes 14 and 15, which
is what all the NE1000 and NE2000 cards use. (The 300 is an 8 bit
pseudo NE1000 clone, and the 400 is a pseudo NE2000 clone.)
5.17. Digital / DEC
5.17.1. DEPCA, DE100/1, DE200/1/2, DE210, DE422
Status -- Supported
As of linux v1.0, there is a driver included as standard for these
cards. It was written by David C. Davies. There is documentation
included in the source file `depca.c', which includes info on how to
use more than one of these cards in a machine. Note that the DE422 is
an EISA card. These cards are all based on the AMD LANCE chip. See
``AMD LANCE'' for more info. A maximum of two of the ISA cards can be
used, because they can only be set for 0x300 and 0x200 base I/O
address. If you are intending to do this, please read the notes in
the driver source file depca.c in the standard kernel source tree.
This driver will also work on Alpha CPU based machines, and there are
various ioctl()s that the user can play with.
5.17.2. Digital EtherWorks 3 (DE203, DE204, DE205)
Status -- Supported
Included into kernels v1.1.62 and above is this driver, also by David
C. Davies of DEC. These cards use a proprietary chip from DEC, as
opposed to the LANCE chip used in the earlier cards like the DE200.
These cards support both shared memory or programmed I/O, although you
take about a 50%performance hit if you use PIO mode. The shared memory
size can be set to 2kB, 32kB or 64kB, but only 2 and 32 have been
tested with this driver. David says that the performance is virtually
identical between the 2kB and 32kB mode. There is more information
(including using the driver as a loadable module) at the top of the
driver file ewrk3.c and also in README.ewrk3. Both of these files
come with the standard kernel distribution. This driver has Alpha CPU
support like depca.c does.
The standard driver has a number of interesting ioctl() calls that can
be used to get or clear packet statistics, read/write the EEPROM,
change the hardware address, and the like. Hackers can see the source
code for more info on that one.
David has also written a configuration utility for this card (along
the lines of the DOS program NICSETUP.EXE) along with other tools.
These can be found on sunsite.unc.edu in the directory
/pub/Linux/system/Network/management -- look for the file ewrk3tools-
X.XX.tar.gz.
5.17.3. DE425 (EISA), DE434, DE435, DE500
Status -- Supported
These cards are based on the 21040 chip mentioned below. Included
into kernels v1.1.86 and above is this driver, also by David C. Davies
of DEC. It sure is nice to have support from someone on the inside
;-) The DE500 uses the newer 21140 chip to provide 10/100Mbs ethernet
connections. Have a read of the 21040 section below for extra info.
Note that as of 1.1.91, David has added a compile time option that
will allow non-DEC cards to work with this driver. Have a look at
README.de4x5 for details.
All the Digital cards will autoprobe for their media (except,
temporarily, the DE500 due to a patent issue).
This driver is also ALPHA CPU ready and supports being loaded as a
module. Users can access the driver internals through ioctl() calls -
see the 'ewrk3' tools and the de4x5.c sources for information about
how to do this.
5.17.4. DEC 21040, 21041, 2114x, Tulip
Status -- Supported
The DEC 21040 is a bus-mastering single chip ethernet solution from
Digital, similar to AMD's PCnet chip. The 21040 is specifically
designed for the PCI bus architecture. SMC's new EtherPower PCI card
uses this chip.
You have a choice of two drivers for cards based on this chip. There
is the DE425 driver discussed above, and the generic 21040 driver that
Donald has written.
Warning: Even though your card may be based upon this chip, the
drivers may not work for you. David C. Davies writes:
``There are no guarantees that either `tulip.c' OR `de4x5.c' will run
any DC2114x based card other than those they've been written to
support. WHY?? You ask. Because there is a register, the General
Purpose Register (CSR12) that (1) in the DC21140A is programmable by
each vendor and they all do it differently (2) in the DC21142/3 this
is now an SIA control register (a la DC21041). The only small ray of
hope is that we can decode the SROM to help set up the driver.
However, this is not a guaranteed solution since some vendors (e.g.
SMC 9332 card) don't follow the Digital Semiconductor recommended SROM
programming format."
In non-technical terms, this means that if you aren't sure that an
unknown card with a DC2114x chip will work with the linux driver(s),
then make sure you can return the card to the place of purchase before
you pay for it.
The updated 21041 chip is also found in place of the 21040 on most of
the later SMC EtherPower cards. The 21140 is for supporting 100Base-?
and works with the Linux drivers for the 21040 chip. To use David's
de4x5 driver with non-DEC cards, have a look at README.de4x5 for
details.
Donald has used SMC EtherPower-10/100 cards to develop the `tulip'
driver. Note that the driver that is in the standard kernel tree at
the moment is not the most up to date version. If you are having
trouble with this driver, you should get the newest version from
Donald's ftp/WWW site.
Tulip Driver
The above URL also contains a (non-exhaustive) list of various
cards/vendors that use the 21040 chip.
Also note that the tulip driver is still considered an alpha driver
(see ``Alpha Drivers'') at the moment, and should be treated as such.
To use it, you will have to edit arch/i386/config.in and uncomment the
line for CONFIG_DEC_ELCP support.
Donald has even set up a mailing list for tulip driver support
announcements, etc. To join it just type:
echo subscribe | /bin/mail linux-tulip-request@cesdis.gsfc.nasa.gov
5.18. Farallon
Farallon sells EtherWave adaptors and transceivers. This device allows
multiple 10baseT devices to be daisy-chained.
5.18.1. Farallon Etherwave
Status -- Supported
This is reported to be a 3c509 clone that includes the EtherWave
transceiver. People have used these successfully with Linux and the
present 3c509 driver. They are too expensive for general use, but are
a great option for special cases. Hublet prices start at $125, and
Etherwave adds $75-$100 to the price of the board -- worth it if you
have pulled one wire too few, but not if you are two network drops
short.
5.19. Hewlett Packard
The 272** cards use programmed I/O, similar to the NE*000 boards, but
the data transfer port can be `turned off' when you aren't accessing
it, avoiding problems with autoprobing drivers.
Thanks to Glenn Talbott for helping clean up the confusion in this
section regarding the version numbers of the HP hardware.
5.19.1. 27245A
Status -- Supported
8 Bit 8390 based 10BaseT, not recommend